GE Vivid S70 User Manual Download Page 240

Page: 240 / 709

4D and Multi-plane Modes

6-40

Vivid S70 / S60

–

User Manual

BC092760-1EN

Figure 6-22. The Bi-plane prepare screen

1. In 4D live press

Bi-plane prepare

on the touch panel.

The

Bi-plane prepare

screen is displayed showing two

perpendicular cut-planes and a smaller volume rendering
with a cross-hair defining the position of the cut-planes.

2. Using the trackball, move the cross-hair in the volume

rendering until the cut-planes of interest are displayed.
Alternatively, adjust

Tilt

and

Rotate

rotary controls.

3. Press

Bi-plane

on the Touch panel (or

Multi D

on the

Control panel) to start high resolution and high frame rate
bi-plane acquisition.

4. Press

Store

to save the acquisition.

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands