GE Vivid S70 User Manual Download Page 472

Page: 472 / 709

Archiving

10-70

Vivid S70 / S60

–

User Manual

BC092760-1EN

Figure 10-52. The Transfer screen

Configuration of Tricefy QR

Tricefy QR, similar to DICOM Query Retrieve, enables users to
check exam results which are stored in the Tricefy website via
scanner.

1. Press

Utility/Config

on the control panel.

2. Select the

Connectivity

category and the

Dataflow

subgroup.

3. Select the dataflow

Tricefy QR -Tricefy Storage

4. Uncheck the

Hidden

button and connect with Internet.

5. Go to patient page and select

Tricefy QR -Tricefy Storage

The exam results stored in the Tricefy website will be
displayed in the

Patients/Exams

list.

NOTE:

Disable Q/R on the Tricefy website to prevent exam data
being used by any other person logging in to the system
with the same IP address.

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands