GE Vivid S70 User Manual Download Page 251

Page: 251 / 709

Selection of a stress test protocol template

Vivid S70 / S60

–

User Manual

7-3

BC092760-1EN

Selection of a stress test protocol

template

1. Press

Stress

on the Touch panel.

The

Protocol

screen is displayed (see Figure 7-1) showing

the default stress protocol for the current probe and
application.

2. Turn freeze off to initiate scanning using the current

template.

To use another template, press

Template

and select the

desired template from the template list. Turn freeze off to
initiate scanning.

NOTE:

To create or edit a template see page 7-26.

Figure 7-1. The Protocol screen

1.  Level selection
2.  Projection selection
3.  Current acquisition
4.  Group of views

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands