GE Vivid S70 User Manual Download Page 198

Page: 198 / 709

Image Optimization

5-62

Vivid S70 / S60

–

User Manual

BC092760-1EN

Figure 5-25. The Scan Assist Pro sheet

4. Select

Import

from the

Scan Assist Pro

sheet.

The

Import Protocols

window is displayed.

Figure 5-26. Import Protocols

5. In the

Source

field, select the media that the Protocol is

stored on.

6. Highlight the Protocol(s) to be imported. If a folder is

highlighted, all Protocols in the folder are selected.

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands