manualshive.com logo in svg

FlightSafety LEARJET 45, Pilot Training Manual, Page: 97 / 539

Share
Download
FlightSafety LEARJET 45 Pilot Training Manual Download Page 97

• Activating the airplane system light

(LTS) test on the system test switch.

• Airplane becomes airborne.

WARNING SYSTEM

LIGHTS

SYSTEM TEST

The CWP and master WARN/CAUT lights are

tested using the system test rotary switch in

the “LTS” position (Figure 4-2). The system

test switch is located on the center pedestal for-

ward of the throttle quadrant. Depressing the

system test knob with the LTS position se-

lected will initiate a test of the following:

• Aural master warn tone (three chimes)

will sound and repeat until the test is re-

leased.

• Master WARN/CAUT lights will flash.

• Progressive test of FGC green lights

• All of the CWP annunciators will illu-

minate.

• Engine “FIRE PUSH” pushbuttons on

the engine/fuel control panel will illu-

minate (steady).

• All switch/indicators (S/Is) will illu-

minate.

• All digit segments on the CPCS (cabin

pressure control system) will illuminate.

• If optional APU is installed - all APU

control panel annunciators and S/Is il-

luminate and white “888” illuminates

in the APU amps display.

If the LTS test is held depressed for more than
15 seconds, the CWP will play through all
t o n e s   a n d   vo i c e   m e s s a g e s   s e q u e n t i a l l y.
Depressing either master WARN/CAUT switch
or the mute switch on the right throttle will
mute the voice messages.

The fire detect lights (FIRE PUSH) are tested
in the LTS position, but the detection system
is tested separately in the “FIRE DET” posi-
tion of the system test switch.

The system test switch is 28 VDC powered

from the left main bus and is protected by a cir-

cuit breaker located on the pilot circuit breaker

panel within the INSTRUMENTS/INDICA-

TIONS group. The circuit breaker is labeled

SYSTEM TEST.

Both master WARN/CAUT lights and the CWP

receive power from the left and right essential

busses. Should one of the essential busses fail

L E A R J E T 4 5

P I L O T   T R A I N I N G   M A N U A L

4-4

FOR TRAINING PURPOSES ONLY

FlightSafety

international

PR

ES

S

TES

T

I3 I . I 5

I I3.80

1

COM

NAV

SQ

NAV

AUDIO

CLR DLY

OFF

G

E
A
R

F

R
E
E

F
A
L
L

P
U
S
H

D
O

W

N

PIT TRIM

BIAS

RUD BOOST

G/S INHB

FLAP OVRD

GPWS

RADIO CTL

HOT BUS

E

L

E
V

P
U

L
L

&

D

I

S
C

SYS TEST/RESET

FLAP

RESET

ANTI

-ICE

SPLRN

RESET

STALL

GPWS

ADC

FLAPS

GEAR

LTS

FIRE

DET

OFF

NDN

MODES

NUP

Honeywell

ON

Figure 4-2.   System Test Switch on Center Pedestal

Summary of Contents for LEARJET 45




























































































































































































































































































































































































































































































































































Reviews:

No comments