manualshive.com logo in svg

D-Link 800 - DFL 800 - Security Appliance, User Manual

The D-Link 800 - DFL 800 - Security Appliance is a top-of-the-line device designed to provide robust security and protection for your network. Equipped with advanced features and functionalities, this product guarantees utmost safety. Enhance your user experience by downloading the comprehensive User Manual for free from our website today.

Share
Download
background image

13.5. Connection Timeout Settings

The settings in this section specify how long a connection can remain idle, that is to say with no data
being sent through it, before it is automatically closed. Please note that each connection has two
timeout values: one for each direction. A connection is closed if either of the two values reaches 0.

TCP SYN Idle Lifetime

Specifies in seconds how long a TCP connection, that is not yet fully established, is allowed to idle
before being closed.

Default: 60

TCP Idle Lifetime

Specifies in seconds how long a fully established TCP connection may idle before being closed.
Connections become fully established once packets with their SYN flags off have travelled in both
directions.

Default: 262144

TCP FIN Idle Lifetime

Specifies in seconds how long a TCP connection about to close may idle before finally being closed.
Connections reach this state when a packet with its FIN flag on has passed in any direction.

Default: 80

UDP Idle Lifetime

Specifies in seconds how long UDP connections may idle before being closed. This timeout value is
usually low, as UDP has no way of signalling when the connection is about to close.

Default: 130

UDP Bidirectional Keep-alive

This allows both sides to keep a UDP connection alive. The default is for NetDefendOS to mark a
connection as alive (not idle) every time data is sent from the side that opened the connection.
Connections that do not receive any data from the opening side within the UDP lifetime will
therefore be closed even if the other side continues to transmit data.

Default: Disabled

Ping Idle Lifetime

Specifies in seconds how long a Ping (ICMP ECHO) connection can remain idle before it is closed.

Default: 8

IGMP Idle Lifetime

Connection lifetime for IGMP in seconds.

Default: 12

13.5. Connection Timeout Settings

Chapter 13. Advanced Settings

439

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 800 - DFL 800 - Security Appliance

IBASE Technology FWA8600 User Manual preview
FWA8600
Brand: IBASE Technology Pages: 112
ZyXEL Communications ENTERPRISE NETWORK CENTER Brochure preview
ENTERPRISE NETWORK CENTER
Brand: ZyXEL Communications Pages: 6
PaloAlto Networks M-300 Hardware Reference Manual preview
M-300
Brand: PaloAlto Networks Pages: 52
HP A-F1000-E Installation Manual preview
A-F1000-E
Brand: HP Pages: 75
St. Bernard iPrism 3000 User Manual preview
iPrism 3000
Brand: St. Bernard Pages: 4

Brands by name

Popular brands

Load more brands