manualshive.com logo in svg

D-Link 800 - DFL 800 - Security Appliance, User Manual

The D-Link 800 - DFL 800 - Security Appliance is a top-of-the-line device designed to provide robust security and protection for your network. Equipped with advanced features and functionalities, this product guarantees utmost safety. Enhance your user experience by downloading the comprehensive User Manual for free from our website today.

Share
Download
background image

13.6. Length Limit Settings

This section contains information about the size limits imposed on the protocols directly under IP
level, such as TCP, UDP and ICMP.

The values specified here concern the IP data contained in packets. In the case of Ethernet, a single
packet can contain up to 1480 bytes of IP data without fragmentation. In addition to that, there is a
further 20 bytes of IP header and 14 bytes of Ethernet header, corresponding to the maximum media
transmission unit on Ethernet networks of 1514 bytes.

Max TCP Length

Specifies the maximum size of a TCP packet including the header. This value usually correlates
with the amount of IP data that can be accommodated in an unfragmented packet, since TCP usually
adapts the segments it sends to fit the maximum packet size. However, this value may need to be
increased by 20-50 bytes on some less common VPN systems.

Default: 1480

Max UDP Length

Specifies in bytes the maximum size of a UDP packet including the header. This value may well
need to be quite high, since many real-time applications use large, fragmented UDP packets. If no
such protocols are used, the size limit imposed on UDP packets can probably be lowered to 1480
bytes.

Default: 60000

Max ICMP Length

Specifies in bytes the maximum size of an ICMP packet. ICMP error messages should never exceed
600 bytes, although Ping packets can be larger if so requested. This value may be lowered to 1000
bytes if you do not wish to use large Ping packets.

Default: 10000

Max GRE Length

Specifies in bytes the maximum size of a GRE packet. GRE, Generic Routing Encapsulation, has
various uses, including the transportation of PPTP, Point to Point Tunneling Protocol, data. This
value should be set at the size of the largest packet allowed to pass through the VPN connections,
regardless of its original protocol, plus approx. 50 bytes.

Default: 2000

Max ESP Length

Specifies in bytes the maximum size of an ESP packet. ESP, Encapsulation Security Payload, is
used by IPsec where encryption is applied. This value should be set at the size of the largest packet
allowed to pass through the VPN connections, regardless of its original protocol, plus approx. 50
bytes.

Default: 2000

Max AH Length

13.6. Length Limit Settings

Chapter 13. Advanced Settings

441

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 800 - DFL 800 - Security Appliance

IBM Proventia Management SiteProtector SP1001 Getting Started preview
Proventia Management SiteProtector SP1001
Brand: IBM Pages: 2
Lanner FW-8759 User Manual preview
FW-8759
Brand: Lanner Pages: 45
ZyXEL Communications ENTERPRISE NETWORK CENTER Manual preview
ENTERPRISE NETWORK CENTER
Brand: ZyXEL Communications Pages: 302
JVC VN-C205U - Network Camera Instructions Manual preview
VN-C205U - Network Camera
Brand: JVC Pages: 46
Intel McAfee Data Loss Prevention Prevent Quick Start Manual preview
McAfee Data Loss Prevention Prevent
Brand: Intel Pages: 8

Brands by name

Popular brands

Load more brands