D-Link 800 - DFL 800 - Security Appliance User Manual Download Page 80 | Manualshive

Page: 80 / 469

background image

3.3. Interfaces

3.3.1. Overview

An Interface is one of the most important logical building blocks in NetDefendOS. All network
traffic that passes through or gets terminated in the system is done so through one or several
interfaces.

An interface can be seen as a doorway for network traffic to or from the system. Thus, when traffic
enters the system through an interface, that interface would be referred to as the receiving interface
(or sometimes ingress or incoming interface). Consequently, when traffic is leaving the system, the
interface used to send the traffic is referred to as the sending interface (or sometimes egress
interface).

NetDefendOS supports a number of interface types, which can be divided into the following four
major groups:

Physical Interfaces

Each physical interface represents a physical port in a
NetDefendOS-based product. Thus, all network traffic that
originates from or is terminated in the system will eventually
pass through any of the physical interfaces.

NetDefendOS currently supports Ethernet as the only physical
interface type. For more information about Ethernet interfaces,
see Section 3.3.2, “Ethernet Interfaces”.

Physical Sub-Interfaces

Some interfaces require a binding to an underlying physical
interface in order to transfer data. This group of interfaces is
called Physical Sub-Interfaces.

NetDefendOS

has

support

for

two

types

of

physical

sub-interfaces:

•

Virtual LAN (VLAN) interfaces as specified by IEEE
802.1Q. When routing IP packets over a Virtual LAN
interface, they will be encapsulated in VLAN-tagged
Ethernet frames. For more information about Virtual LAN
interfaces, please see Section 3.3.3, “VLAN”.

•

PPPoE (PPP-over-Ethernet) interfaces for connections to
PPPoE servers. More information about this topic can be
found in Section 3.3.4, “PPPoE”.

Tunnel Interfaces

Tunnel interfaces are used when network traffic is being
tunneled between the system and another tunnel end-point in
the network, before it gets routed to its final destination.

To accomplish tunneling, additional headers are added to the
traffic

that

is

to

be

tunneled.

Furthermore,

various

transformations can be applied to the network traffic depending
on the type of tunnel interface. For example, when routing
traffic over an IPsec interface, the payload is usually encrypted
to achieve confidentiality.

NetDefendOS supports the following tunnel interface types:

•

IPsec interfaces are used as end-points for IPsec VPN
tunnels. More information about this topic can be found in
Section 9.3, “IPsec Components”.

•

PPTP/L2TP interfaces are used as end-points for PPTP or
L2TP tunnels. More information about this topic can be

3.3. Interfaces

Chapter 3. Fundamentals

80

«
...
78
79
80
81
82
...
»

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 800 - DFL 800 - Security Appliance

ENTERPRISE NETWORK CENTER

Brand: ZyXEL Communications Pages: 302

NCA-4010 Series

Brand: Lanner Pages: 111

Brand: Lanner Pages: 97

FortiWiFi FortiWiFi-50B

Brand: Fortinet Pages: 68

NetDefend DFL Series

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

DFL-1100 - Security Appliance

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 32

Brand: Barracuda Pages: 6

Brand: Fortinet Pages: 240

QRadar XGS 5200

Brand: IBM Pages: 8

NetDefend DFL-CP310

Brand: D-Link Pages: 455

NetDefend SOHO DFL-160

Brand: D-Link Pages: 356

DFL-1600 - Security Appliance

Brand: D-Link Pages: 552

Brand: GROM Audio Pages: 153

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands