manualshive.com logo in svg

D-Link 800 - DFL 800 - Security Appliance, User Manual, Page: 177 / 469

Share
Download
D-Link 800 - DFL 800 - Security Appliance User Manual Download Page 177

•

Destination Interface: dmz

•

Source Network: all-nets

•

Destination Network: wan_ip

9.

Click OK

4.7.4. Spanning Tree BPDU Support

NetDefendOS includes support for relaying the Bridge Protocol Data Units (BPDUs) across the
D-Link Firewall. BPDU frames carry Spanning Tree Protocol (STP) messages between layer 2
switches in a network. STP allows the switches to understand the network topology and avoid the
occurrences of loops in the switching of packets.

The diagram below illustrates a situation where BPDU messages would occur if the administrator
enables the switches to run the STP protocol. Two D-Link Firewalls are deployed in transparent
mode between the two sides of the network. The switches on either side of the firewall need to
communicate and require NetDefendOS to relay switch BPDU messages in order that packets do not
loop between the firewalls.

Figure 4.16. An Example BPDU Relaying Scenario

Implementing BPDU Relaying

The NetDefendOS BDPU relaying implementation only carries STP messages. These STP messages
can be of three types:

•

Normal Spanning Tree Protocol (STP)

•

Rapid Spanning Tree Protocol (RSTP)

•

Multiple Spanning Tree Protocol (MSTP)

•

Cisco proprietary PVST+ Protocol (Per VLAN Spanning Tree Plus)

NetDefendOS checks the contents of BDPU messages to make sure the content type is supported. If
it is not, the frame is dropped.

Enabling/Disabling BPDU Relaying

BPDU relaying is disabled by default and can be controlled through the advanced setting Relay
Spanning-tree BPDUs. Logging of BPDU messages can also be controlled through this setting.
When enabled, all incoming STP, RSTP and MSTP BPDU messages are relayed to all transparent
interfaces in the same routing table, except the incoming interface.

4.7.5. Advanced Settings for Transparent Mode

CAM To L3 Cache Dest Learning

Enable this if the firewall should be able to learn the destination for hosts by combining destination
address information and information found in the CAM table.

4.7.4. Spanning Tree BPDU Support

Chapter 4. Routing

177

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments