D-Link 800 - DFL 800 - Security Appliance User Manual Download Page 52 | Manualshive

Page: 52 / 469

background image

•

Category - What NetDefendOS subsystem is reporting the problem

•

ID - Unique identification within the category

•

Description - A short textual description

•

Action - What action is NetDefendOS taking

This information can be cross-referenced to the Log Reference Guide.

Note

NetDefendOS sends SNMP Traps which are based on the SNMPv2c standard as
defined by RFC1901, RFC1905 and RFC1906.

Example 2.12. Sending SNMP Traps to an SNMP Trap Receiver

To enable generation of SNMP traps for all events with a severity greater than or equal to Alert to an SNMP trap
receiver with an IP address of 195.11.22.55, follow the steps outlined below:

CLI

gw-world:/> add LogReceiver EventReceiverSNMP2c my_snmp IPAddress=195.11.22.55

Web Interface

1.

Go to Log & Event Receivers > Add > SNMP2cEventReceiver

2.

Specify a name for the event receiver, for example my_snmp

3.

Enter 195.11.22.55 as the IP Address

4.

Enter an SNMP Community String if needed by the trap receiver

5.

Click OK

The system will now be sending SNMP traps for all events with a severity greater than or equal to Alert to an
SNMP trap receiver at 195.11.22.55.

2.2.4. Advanced Log Settings

The following advanced settings for logging are available to the administrator:

Send Limit

This setting limits how many log packets NetDefendOS may send out per second. This value should
never be set too low, as this may result in important events not being logged, nor should it be set too
high.

A situation where setting too high a value may cause damage is when NetDefendOS sends a log
message to a server whose log receiver is not active. The server will send back an ICMP
UNREACHABLE message, which may cause NetDefendOS to send another log message, which in
turn will result in another ICMP UNREACHABLE message, and so on. By limiting the number of
log messages NetDefendOS sends every second, you avoid encountering such devastating
bandwidth consuming scenarios.

Default: 3600 (once per hour)

Alarm Repetition Interval

2.2.4. Advanced Log Settings

Chapter 2. Management and Maintenance

52

«
...
50
51
52
53
54
...
»

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 800 - DFL 800 - Security Appliance

STM150 - ProSecure Web And Email Threat Management Appliance

Brand: NETGEAR Pages: 2

STM150 - ProSecure Web And Email Threat Management Appliance

Brand: NETGEAR Pages: 248

Brand: Lanner electronics Pages: 48

Brand: IronPort Pages: 3

Brand: tufin Pages: 22

Brand: Clavister Pages: 4

NetWall 100 Series

Brand: Clavister Pages: 81

Brand: Clavister Pages: 76

Brand: Clavister Pages: 94

Brand: CyberGuard Pages: 22

Brand: CyberGuard Pages: 185

Brand: CyberGuard Pages: 189

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands