manualshive.com logo in svg

D-Link 800 - DFL 800 - Security Appliance, User Manual

The D-Link 800 - DFL 800 - Security Appliance is a top-of-the-line device designed to provide robust security and protection for your network. Equipped with advanced features and functionalities, this product guarantees utmost safety. Enhance your user experience by downloading the comprehensive User Manual for free from our website today.

Share
Download
background image

•

Check that the correct certificates have been used.

•

Check that the certificate .cer and .key files have the same filename. For example, my_cert.key
and my_cert.cer.

•

Check that the certificates have not expired.

•

Check that the NetDefendOS date and time is set correctly and consider time-zone issues with
newly generated certificates (the time of generation may not be the same as the CA server's
system time).

•

Disable CRL (revocation list) checking to see if CA server access could be the problem. CA
Server issues are discussed further in Section 9.6, “CA Server Access”.

Troubleshooting IPsec Tunnels

A number of commands can be used to diagnose IPsec tunnels:

The ipsecstat console command

ipsecstat can be used to show that IPsec tunnels have correctly established. A representative
example of output is:

> ipsecstat

--- IPsec SAs:

Displaying one line per SA-bundle

IPsec Tunnel

Local Net

Remote Net

Remote GW

------------

--------------

------------

-------------

L2TP_IPSec

214.237.225.43

84.13.193.179

84.13.193.179

IPsec_Tun1

192.168.0.0/24

172.16.1.0/24

82.242.91.203

To examine the first IKE negotiation phase of tunnel setup use:

> ipsecstat -ike

To get complete details of tunnel setup use:

> ipsecstat -u -v

The ikesnoop console command

A common problem with setting up IPsec is a list of proposed algorithms that is unacceptable to the
device at the other end of the tunnel. The ikesnoop command is a useful tool for diagnosing
incompatible algorithm proposal lists by showing the details of negotiations during tunnel setup.
The basic form of this command is:

ikesnoop -on -verbose

Once issued, an ICMP ping can then be sent to the D-Link Firewall from the remote end of the
tunnel. This will cause ikesnoop to output details of the tunnel setup negotiation to the console and
any algorithm proposal list incompatibilities can be seen.

If there are multiple tunnels in a setup or multiple clients on a single tunnel then the output from
verbose option can be overwhelming. It is therefore better to specify that the output comes from a

Troubleshooting IPsec Tunnels

Chapter 9. VPN

375

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 800 - DFL 800 - Security Appliance

Watchguard 970 Quick Start Manual preview
970
Brand: Watchguard Pages: 8
Honeywell Sucre Box + Quick Start Manual preview
Sucre Box +
Brand: Honeywell Pages: 2
Barracuda Networks Spam Firewall Outbound Quick Start Manual preview
Spam Firewall Outbound
Brand: Barracuda Networks Pages: 2
Sophos XGS 116 Quick Start Manual preview
XGS 116
Brand: Sophos Pages: 68
Barracuda CloudGen Firewall F1000 CE0 Quick Start Manual preview
CloudGen Firewall F1000 CE0
Brand: Barracuda Pages: 8
3Com SUPERSTACK 3CR16110-95 Quick Reference Manual preview
SUPERSTACK 3CR16110-95
Brand: 3Com Pages: 4
IBM GX7000 Series Getting Started Instructions preview
GX7000 Series
Brand: IBM Pages: 7
Trend Micro txOne Networks EdgeIPS Quick Setup Manual preview
txOne Networks EdgeIPS
Brand: Trend Micro Pages: 5

Brands by name

Popular brands

Load more brands