D-Link 800 - DFL 800 - Security Appliance User Manual Download Page 405 | Manualshive

Page: 405 / 469

background image

10.4.5. Server Health Monitoring

SLB uses Server Health Monitoring to continuously check the condition of the servers in an SLB
configuration. SLB can monitor different OSI layers to check the condition of each server.
Regardless of the algorithms used, if a server is deemed to have failed, SLB will not open any more
connections to it until the server is restored to full functionality.

D-Link Server Load Balancing provides the following monitoring modes:

ICMP Ping

This works at OSI layer 3. SLB will ping the IP address of each individual
server in the server farm. This will detect any failed servers.

TCP Connection

This works at OSI layer 4. SLB attempts to connect to a specified port on
each server. For example, if a server is specified as running web services on
port 80, the SLB will send a TCP SYN request to that port. If SLB does not
receive a TCP SYN/ACK back, it will mark port 80 on that server as down.
SLB recognizes the conditions no response, normal response or closed port
response from servers.

10.4.6. SLB_SAT Rules

The key component in setting up SLB is the SLB_SAT rule in the IP rule set. The steps that should
be followed are:

1.

Define an Object for each server for which SLB is to be done.

2.

Define a Group which included all these objects.

3.

Define an SLB_SAT Rule in the IP rule set which refers to this Group and where all other SLB
parameters are defined.

4.

Define a further rule that duplicates the source/destination interface/network of the SLB_SAT
rule that allows traffic through. This could be one rule or a combination of:

•

ForwardFast

•

Allow

•

NAT

The table below shows the rules that would be defined for a typical scenario of a set of webservers
behind the D-Link Firewall for which the load is being balanced. The Allow rule allows external
clients to access the webservers.

Rule Name

Rule Type

Src. Interface

Src. Network

Dest. Interface

Dest. Network

WEB_SLB

SLB_SAT

any

all-nets

core

ip_ext

WEB_SLB_ALW

Allow

any

all-nets

core

ip_ext

If there are clients on the same network as the webservers that also need access to those webservers
then an NAT rule would also be used:

Rule Name

Rule Type

Src. Interface

Src. Network

Dest. Interface

Dest. Network

WEB_SLB

SLB_SAT

any

all-nets

core

ip_ext

WEB_SLB_NAT

NAT

lan

lannet

core

ip_ext

WEB_SLB_ALW

Allow

any

all-nets

core

ip_ext

Note that the destination interface is specified as core, meaning NetDefendOS itself deals with this.
The key advantage of having a separate Allow rule is that the webservers can log the exact IP
address that is generating external requests. Using only a NAT rule, which is possible, means that

10.4.6. SLB_SAT Rules

Chapter 10. Traffic Management

405

«
...
403
404
405
406
407
...
»

Summary of Contents for 800 - DFL 800 - Security Appliance






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 800 - DFL 800 - Security Appliance

FortiMail-5001A

Brand: Fortinet Pages: 2

FortiManager-100

Brand: Fortinet Pages: 2

FortiGate FortiGate-5002FB2

Brand: Fortinet Pages: 2

FortiGate ASM-FX2

Brand: Fortinet Pages: 1

SuperMassive 9800 AC

Brand: SonicWALL Pages: 2

Brand: SonicWALL Pages: 2

Brand: SonicWALL Pages: 2

Brand: SonicWALL Pages: 4

Secure Mobile Access 6210

Brand: SonicWALL Pages: 2

Brand: SonicWALL Pages: 2

Brand: SonicWALL Pages: 2

Brand: SonicWALL Pages: 9

TZ 150 Wireless

Brand: SonicWALL Pages: 37

Brand: SonicWALL Pages: 46

SuperMassive 9800

Brand: SonicWALL Pages: 76

SonicOS Enhanced 2.2

Brand: SonicWALL Pages: 190

StoneGate SG-200

Brand: Stonesoft Pages: 25

Brand: Stonesoft Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands