Creo Color Controller C-80 Technical Manual Download Page 139

Page: 139 / 150

123

5.10 Replacing Fans

Perform the following procedures to remove and install the rear fan and PCI fan.

Figure 44: Rear and PCI fan connector locations

5.10.1 Removing the Rear Fan

1. Review

Safety Information (Multi-Language)

on page v.

2. Turn off the Color Controller C-80 and peripheral devices. Disconnect all AC

power cords and external cables.

3. Remove the side cover. See

Removing the Side Cover

on page 94.

4. Disconnect the fan cable from the system board connector (Fan 5).

5. Press the two locking tabs, protruding through the outside of the rear of the

server, outward. See Figure 45 on page 124.

6. Lift the fan upward and out of the server.

Connector Fan5
(Rear fan)

Connector Fan4
PCI fan)

Summary of Contents for Color Controller C-80























































































































































Search results

Summary of Contents for Color Controller C-80

Reviews:

Related manuals for Color Controller C-80

Brands by name

Popular brands

Creo Color Controller C-80, Technical Manual

Search results

Summary of Contents for Color Controller C-80

Reviews:

Related manuals for Color Controller C-80

Brands by name

Popular brands