COBHAM GR716 Advanced Data Sheet And User’S Manual Download Page 83 | Manualshive

Page: 83 / 547

COBHAM GR716 Advanced Data Sheet And User’S Manual Download Page 83

GR716-DS-UM, May 2019, Version 1.29

85

www.cobham.com/gaisler

GR716

17: 16

SpaceWire Loop-back control (SPW) - Control of SpaceWire loop-back production test.

Bit #17 - Enable internal loop-back for SpaceWire PHY 0 (LVDS)



Bit #16 - Enable internal loop-back for SpaceWire PHY 1 (CMOS)

Internal loop-back means that the ports internal data and strobe signals are not mapped to the corresponding
external SpaceWire I/O pins. They are instead routed back to the port internally (transmit data to receive data,
transmit strobe to receive strobe).

15

LVDS External Loop (LL) - Enable LVDS external loop-back.

External loop-back means that the external LVDS I/O pins are not routed to the corresponding port. Instead they
are routed back out on the external pins (LVDS_RXp/n to LVDS_TXp/n). Enable of external loop-back forces
the LVDS receiver and transmitter to be enabled.

LVDS external loop-back mode enables external test of voltage input and low level detection.

14: 13

SpaceWire External Loop (LS) - SpaceWire external loop-back

0x0 - Normal operation



0x1 - External loop-back mode routed back via rising edge clocked flip-flops



0x2 - External loop-back mode routed back via falling edge clocked flip-flops



0x3 - External loop-back mode routed back via rising or falling edge clocked flip-flops

SpaceWire External loop-back means that the external SpaceWire I/O pins are routed via SpaceWire-Phy to the
corresponding port. Pins are routed back via SpaceWire-Phy out on the external pins (SPW_RXDp/n to
SPW_TXDp/n and SPW_RXSp/n to SPW_TXSp/n).

Test option 0x1 and 0x2 are used for setup and hold measurements for respective clock edge. Test option 0x3 is
used for minimum pulse width detection.

12

Locken (LE) - Support Locked transfers in SCRUBBER.

11

Force Scrubber (FS) - Force Scrubber to function as AHBSTAT unit on main AMBA bus.

10: 9

Interrupt test protection bits (PROT) - Protection and generation of interrupt test for specified interrupt source.

The protection bits needs to be toggled in-order to generate a test interrupt i.e.both PROT bits needs to be read
and bitwise inverted before written back to the PROT bit-field to generate a interrupt.

8:3

Interrupt source (IRQ) - An event will be generated on the interrupt source

2

MIL-1553B reset disable (MR) - Disable reset signal from MIL-1553B core

1

Override watchdog error generation (WE) - Disables reset request. To be used during debug of the system

0

Override error generation (EE) - Disables reset generation when processor error is detected. To be used during
debug of the system

Table 66.

0x8000E000 - SYS.CFG.SCFG - Interrupt test configuration register

«
...
81
82
83
84
85
...
»

Summary of Contents for GR716




































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands