manualshive.com logo in svg

COBHAM GR716, Advanced Data Sheet And User’S Manual, Page: 207 / 547

Share
Download
COBHAM GR716 Advanced Data Sheet And User’S Manual Download Page 207

GR716-DS-UM, May 2019, Version 1.29

209

www.cobham.com/gaisler

GR716

A write access to the register initiates an analogue to digital conversion, provided that no other ADC

 

or DAC conversion is ongoing (otherwise the request is rejected).
A read access that occurs before an ADC conversion has been completed returns the result from a pre-
vious conversion. 
Note that any data can be written and that it cannot be read back, since not relevant to the initiation of 
the conversion.
Note that only the part of ADI.Din[15:0] that is specified by means of bit ADCONF.ADCDW is used 
by the ADC. The rest of the bits are read as zeros. 

24.3.4 DAC Data Output Register [ADOUT] R/W

Table 227.

DAC Data Output Register

15-0: 

DACOUT DAC output data

ADO.Dout[15:0]

A write access to the register initiates a digital to analogue conversion, provided that no other DAC or 
ADC conversion is ongoing (otherwise the request is rejected).
Note that only the part of ADO.Dout[15:0] that is specified by means of ADCONF.DACDW is driven 
by the DAC. The rest of the bits are not driven by the DAC during a conversion. 
Note that only the part of ADO.Dout[15:0] which is specified by means of ADCONF.DACDW can be 
read back, whilst the rest of the bits are read as zeros. 

24.3.5 Address Input Register [ADAIN] R

Table 228.

Address Input Register

7-0: 

AIN

Input address 

ADI.Ain[7:0]

All bits are cleared to 0 at reset. 

24.3.6 Address Output Register [ADAOUT] R

Table 229.

Address Output Register

/W

7-0: 

AOUT

Output address 

ADO.Aout[7:0]

All bits are cleared to 0 at reset. 

24.3.7 Address Direction Register [ADADIR] R

Table 230.

Address Direction Register

/W

7-0: 

ADIR

Direction: 

ADO.Aout[7:0]

31

16

15

0

DACOUT

31

8

7

0

AIN

31

8

7

0

AOUT

31

8

7

0

ADIR

Summary of Contents for GR716




































































































































































































































































































































































































































































































































































Reviews:

No comments