7
7
7-14
7-14
Error Code > Error Code > Error Code Details
Error Code > Error Code > Error Code Details
Code
Detail
Code
Location
Item
Description
E020 1000 05
Title
Error in light intensity correction of patch sensor LED
Description
of detection
Detected value is below the specified value at the light
intensity correction of patch sensor LED
Measures 1. Check the connector of the patch sensor (PS9).
2. Check the connector of the ITB driver PCB (PCB6).
3. Check the connector of the DC controller PCB (PCB1).
4. Replace the patch sensor (PS9).
5. Replace the ITB driver PCB (PCB6).
6. Replace the DC controller PCB (PCB1).
E023 0010 05
Title
Error in developing motor
Description
of detection
Error in sleeve motor. Lock is unlocked 5 times repeatedly
during the operation.
Measures Check the connector of the developing sleeve motor (M1),
and replace the motor if necessary.
E023 0011
05
Title
Error in developing motor
Description
of detection
Error in sleeve motor. Invalid lock is detected during standby.
Measures Check the connector of the developing sleeve motor (M1),
and replace the motor if necessary.
E023 0020 05
Title
Error in developing stirring motor
Description
of detection
While the motor is driving, the lock has come off for 3
sec continuously (come off 30 times with 100 msec cycle
including 2 sec stability time).
Measures 1. Check the connector of the developing stirring motor (M2).
2. Check the connector of the developing driver PCB (PCB5).
3. Check the connector of the drawer on developing
assembly.
4. Check the connector of the DC controller PCB (PCB1).
5. Replace the developing stirring motor (M2).
6. Replace the developing driver PCB (PCB5).
7. Replace the DC controller PCB (PCB1).
E025 0000 05
Title
Error in hopper stirring motor
Description
of detection
While the motor is driving, the lock has come off for 3
sec continuously (come off 30 times with 100 msec cycle
including 2 sec stability time).
Measures 1. Check the connector of the hopper stirring motor (M68).
2. Check the connector of the hopper driver PCB (PCB46).
3. Check the connector of the fixing main driver PCB (PCB8).
4. Check the connector of the DC controller PCB (PCB1).
5. Replace the hopper stirring motor (M68).
6. Replace the hopper driver PCB (PCB46).
7. Replace the fixing main driver PCB (PCB8).
8. Replace the DC controller PCB (PCB1).
Code
Detail
Code
Location
Item
Description
E028 0001 05
Title
Error in toner bottle movement
Description
of detection
Position sensor does not go ON within the specified time (3
sec) after the toner bottle is slid back and forth.
Measures Check the connector of the toner container slide motor (M67),
and replace the motor if necessary.
E032 0001 00
Title
NE controller counter is not working
Description
of detection
Count pulse signal breaking is detected
Measures Cable check
E060 0000 05
Title
Error in wire movement
Description
of detection
When the wire cleaning material does not move front even
though it is shifted toward front for 10 sec.
Measures Check the connector of the primary charging wire cleaner
position sensor 1 (PS160), and replace the sensor if
necessary.
E060 0001 05
Title
Error in wire movement
Description
of detection
When the wire cleaning material does not move rear even
through it is shifted toward rear for 10 sec.
Measures Check the connector of the primary charging wire cleaner
position sensor 2 (PS161), and replace the sensor if
necessary.
E061 0001 05
Title
Error in potential control
Description
of detection
When VL potential is 600V or more on the pre-rotation VL
potential detection interval.
Measures 1. Check the connector of the potential sensor.
2. Check the connection of the potential sensor harness.
3. Replace the potential sensor.
E061 0002 05
Title
Error in potential control
Description
of detection
At potential control execution, when the grid bias 750V is
applied and if Vd potential is 700V or more.
Measures 1. Check the connector of the potential sensor.
2. Check the connector of the pre-exposure LED.
3. Replace the potential sensor.
4. Replace the pre-exposure LED.
E061 0003 05
Title
Error in potential control
Description
of detection
At potential control execution, when the grid bias 500V and
900V is applied and if Vd potential difference is 50V or less.
Measures 1. Check the connector of the potential sensor, and replace
the sensor if necessary.
2. Check the connector of the video signal harness (abnormal
laser emission)
3. Replace the primary charging wire.
4. Abnormal high voltage (primary high-voltage, grid high-
voltage)
Summary of Contents for imagePRESS 1110
Page 242: ...3 3 Periodical Service Periodical Service Periodical service item ...
Page 655: ...5 5 Adjustment Adjustment Overview When replacing parts Major adjustment ...
Page 944: ...8 8 Service Mode Service Mode Overview COPIER FEEDER SORTER BOARD Situation Mode ...
Page 1555: ... Service Tools General Circuit Diagram General Timing Chart Operator Maintenance Appendix ...