Bull Escala BL460, Problem Determination And Service Manual, Page: 155 / 266

Chapter 2. Diagnostics
135
SRN Description FRU/action
A12-13x
A non-critical error has been detected, a I/O
host bridge address/data parity error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A12-15x
A non-critical error has been detected, a
system support function error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A12-16x
A non-critical error has been detected, a
system bus internal hardware/switch error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A12-50x
Recoverable errors on resource indicate a
trend toward an unrecoverable error.
However, the resource could not be
deconfigured and is still in use.
The system is operating with the potential for
an unrecoverable error.
1. If repair is not immediately available, reboot and the
resource will be deconfigured; operations can
continue in a degraded mode.
2. Check the management-module event log for an entry
around this time. If no entry is found, replace the
system-board and chassis assembly.
A13-00x
A non-critical error has been detected, a
error log analysis indicates an error detected
by the I/O device, but the failure could not
be isolated.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-01x
A non-critical error has been detected, an
I/O bus address parity error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-02x
A non-critical error has been detected, an
I/O bus data parity error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-03x
A non-critical error has been detected, an
I/O bus time-out, access or other error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-04x
A non-critical error has been detected, an
I/O bridge/device internal error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-05x
A non-critical error has been detected, an
I/O error on non-PCI bus.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-06x
A non-critical error has been detected, a
mezzanine bus address parity error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.
A13-07x
A non-critical error has been detected, a
system bus address parity error.
1. Check the management-module event log; if an error
was recorded by the system, see “ POST progress
codes (checkpoints) ” on page 71 .
2. If no entry is found, replace the system-board and
chassis assembly.