Asentria TeleBoss 830 User Manual Download Page 42

Page: 42 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 42

Name Resolution Settings

This submenu is used to set up to two Domain Name Servers. DNS servers allow for the use of host names

rather than IP addresses in functions where name resolution may be needed, such as; Email server, action IP

settings, network time servers, scripting TCP connections, etc. The DNS Mode can also be toggled between

MANUAL, ETH1-DHCP, ETH2-DHCP, and DSL.

TeleBoss 830 - Name Resolution Settings
A) DNS Server 1 [0.0.0.0]
B) DNS Server 2 [0.0.0.0]
C) DNS Mode [MANUAL]

DNS Server 1

and

DNS Server 2

DNS Server 1 and 2 are the IP addresses of Domain Name Servers so that you can use host names rather

than IP addresses. The default setting for each DNS Server is 0.0.0.0.

DNS Mode

The DNS Mode toggles between MANUAL, ETH1-DHCP, ETH2-DHCP, and DSL. The default setting is

MANUAL.

Name Resolution Settings as accessed via Web UI

These same settings can be configured in the Web interface by navigating to Networking in the Settings Menu

section of the Web GUI and choosing the Network submenu.

IP Record Collection Settings

The TeleBoss can collect text records via various Internet Protocols. The call records, or other text data, can

then be stored in a data file. The

supports the following IP Record Collection protocols/IP-enabled

switches:

Generic Server

Avaya

– Reliable Session Protocol

Alcatel OmniPCX

CCM4 (Cisco CallManager version 4.x)

Summary of Contents for TeleBoss 830






























































































































































Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands

Asentria TeleBoss 830, User Manual

Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands