manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 121

TeleBoss 830 2.11.370 STD User Manual 

 

Page 121 

 

 

Callout Delay

  

Set the time in seconds (0 - 400) to wait between callout attempts.  The default setting is 60 seconds. 

 

Action Schedule

  

This menu option displays the Action Schedule Settings menu where actions can be limited to defined days 

and times.  

 

Reminder Interval

  

Set the time in minutes (0 

– 65535) at which an action is repeated if the sensor (contact closure, temperature, 

humidity, or voltage) that triggered the alarm is still in the active (alarm) state.  When the sensor has been 

returned to the inactive (normal) state, the reminder interval is no longer in effect.  The default setting is 120 

minutes. 

 

Asentria Alarm Version

  

This option toggles between 1.0 and 1.1 to indicate which type of Asentria Alarm notification will be displayed.  

Set this 1.0 for the Dialup POTs modem.  Set it at 1.1 if you are using other delivery methods for your alarm 

actions.  The default setting is 1.1 

 

Require Asentria Alarm ACKs

  

This is an ON/OFF toggle to enable or disable forcing the unit to require an acknowledgment when first 

connecting, and after each Asentria Alarm.  If disabled, the TeleBoss will allow non-CRC mode where 

Asentria Alarms are delivered without waiting for any indication that the messages were properly delivered.  If 

enabled, CRC mode is required by the TeleBoss.  The default setting is OFF. 

 

 

Action Schedule 

Use this menu to limited alarm actions to defined days and times. 

 

 

TeleBoss 830 - Action Schedule Settings 
A) Action Schedule Enable               [OFF] 
B) Begin Time                           [08:00] 
C) End Time                             [17:00] 
D) Weekdays Only                        [ON] 

 

 

Actions Schedule Enable

  

This is an ON/OFF toggle to enable the action schedule.  The default setting is OFF. 

 

Begin Time / End Time

  

Use these options to set the beginning and ending times (24 hour clock) during which alarm actions can be 

taken.  The default settings are 08:00 (Begin Time) and 17:00 (End Time). 

 

Weekdays Only  

This is an ON/OFF Toggle to set whether actions are only performed Monday thru Friday.  The default setting 

is ON. 

 
 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands