manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 13

TeleBoss 830 2.11.370 STD User Manual 

 

Page 13 

 

g.  Enter a Subnet mask and router address, if needed, using options 

C

 and 

D

. 

h.  Press Enter to go back one level in the menu tree, or <CTRL + C> to exit the Setup Menu and return 

to the command prompt.    

 

 

Note: 

The TeleBoss does not heed changes to network configurations while you are connected to a 

command processor via Telnet. Changes are pended until all network-based command processor 

sessions have ended.  To exit from the TeleBoss Command processer type 

BYE

 and press <Enter>

. 

Optionally you may type 

RESTART

 and press <Enter> at the command prompt to restart the unit to 

ensure all command processors are closed.  

 

Testing Network Connectivity 

Once the network settings are configured connect to the Web Interface by inputting the Ethernet address set 

for Ethernet 1 into a Chrome, Internet Explorer or Firefox browser.  The TeleBoss password page will appear.   

 

If you are connected serially to the Command interface you can verify that the network connectivity is 

available to the unit by typing the command

 PING <IP_address> 

at the TeleBoss command prompt

.

  A router 

is always a good candidate for test pings but any reachable IP address can be used.  The following 

screenshot is an example of a successful ping test. 

 

 

>ping 192.168.100.25 
PING 192.168.100.25 (192.168.100.25) 56(84) bytes of data. 
64 bytes from 192.168.100.25: icmp_seq=1 ttl=64 time=0.375 ms 
64 bytes from 192.168.100.25: icmp_seq=2 ttl=64 time=0.317 ms 
64 bytes from 192.168.100.25: icmp_seq=3 ttl=64 time=0.325 ms 
64 bytes from 192.168.100.25: icmp_seq=4 ttl=64 time=0.317 ms 
64 bytes from 192.168.100.25: icmp_seq=5 ttl=64 time=0.292 ms 
64 bytes from 192.168.100.25: icmp_seq=6 ttl=64 time=0.318 ms 
64 bytes from 192.168.100.25: icmp_seq=7 ttl=64 time=0.315 ms 
 
--- 192.168.100.25 ping statistics --- 
7 packets transmitted, 7 received, 0% packet loss, time 6006ms 
rtt min/avg/max/mdev = 0.292/0.322/0.375/0.031 ms 
 

 

Press 

CTRL + C

 keys to stop the ping testing.  If CTRL + C are not pressed, the unit will continue pinging 

attempts until the active command process is closed.  Alternately, a ping count can be defined in the 

command string, 

PING 192.168.100.25 -C5, 

to limit the ping requests. 

  

If there is an error message or no response from the router, first check the network settings and connection.   

Consult your System Administrator or 

Asentria Technical Support

 for additional assistance. 

 

Once the TeleBoss is successfully connected to the network the unit can be configured via either interface.  

The Web Interface can be accessed by inputting the Ethernet address set for Ethernet 1 into a Chrome, 

Internet Explorer or Firefox browser or you can proceed to configure your unit as needed via the Command 

Line Interface using the 

SETUP

 menu and/or settings keys. 

 

 

 

 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands