manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 94

TeleBoss 830 2.11.370 STD User Manual     

 

Page 94 

 

 

 

 

SSL Certificate via Web Interface 

The purpose of the Certificate section of the Web UI is to allow a MASTER user to configure SSL certificates 

used to access the unit via HTTPS.  This HTTPS Web UI section allows the MASTER user to create a self-

signed certificate, create a certificate signing request (CSR), install an externally signed certificate, and check 

the status of these 3 things. 

 

The benefit is that a user can install a certificate signed (externally) by a certificate authority that is by default 

trusted by web browsers, thus eliminating the SSL warning in the browser when you browse via HTTPS to the 

unit. 

 

 

 

Common Name 

This is a Text field to name the unit. The maximum number of characters is 64.  The default is teleboss. 

 

Organization Unit 

This is a text field.  The maximum number of characters is 40. The default is Technical Services. 

 

Organization 

This is a text field.  The maximum number of characters is 40. The default is Asentria. 

 

Key Length 

This drop down box allows the user to select the SSL key length.  The options are 1024 bits or 2048 bits.  The 

default is 1024 bits. 

 

Locality 

This is a text field.  The maximum number of characters is 40.  The default is Seattle. 

 

State/Province 

This is a text field.  The maximum number of characters is 40.  The default is Washington. 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands