manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 110

TeleBoss 830 2.11.370 STD User Manual     

 

Page 110 

 

 

Sensor Unresponsive Settings 

The Sensor Unresponsive Menu is where you can configure the actions the TeleBoss takes if an 

EventSensor becomes unresponsive. 

 

 
TeleBoss 830 - Sensor Unresponsive Menu 
A) Sensor Unresponsive Timeout                       [30] 
B) Sensor Unresponsive Actions                       [] 
C) Sensor Unresponsive Trap Number                   [50] 
D) Sensor Unresponsive Class                         [Info] 
 

 

Sensor Unresponsive Timeout

  

This sets the time (10 - 65535 seconds) to wait before declaring a non-communicative EventSensor 

unresponsive.  The default setting is 30. 

 

Sensor Unresponsive Actions

  

Choosing this option displays the Actions List, a menu where the action string for the event is configured.  

This field will be empty [ ] if no actions have been configured, and will show [*SET*] if one or more actions 

have been configured.  Refer to 

Actions List 

for more information. 

 

Sensor Unresponsive Trap Number

  

This sets the trap number to be sent with any SNMP traps for this event.  The default is 50, but the trap 

number can also be set in the range of 1000 

– 1199 as needed. 

 

Sensor Unresponsive Class

  

Use this option to set the class for the alarm.  When this option is selected, a list of the classes previously 

defined in the 

Class Table

 is displayed.   Select one to be assigned to this event.  The default is Info. 

 

 

General Sensor Unresponsive Settings as accessed via Web UI 

The Senor Unresponsive settings would be accessed from the EventSensor submenu under the Events 

section on the left hand menu.  The settings described above are located at the bottom of the page 

EventSensor Settings page. 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands