manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 61

TeleBoss 830 2.11.370 STD User Manual 

 

Page 61 

 

 

 

 

FTP Settings 

This menu is used to configure automatic FTP pushes of buffered data.  When the unit pushes the data the 

records are moved to the configured server and are automatically deleted from the TeleBoss file. 

 

 

Note:

 

There is no menu option to set “FTP Auto-delete”, a setting that will cause all data in the file to be 

deleted when polled via the FTP ‘get’ function.  To enable FTP Auto-delete, set 

net.ftp.autodel

=ON

. 

 

Testing FTP Push 

Once FTP Push has been configured, entering the 

PUSHTEST

 command from the command prompt will test 

the connectivity to the FTP server and write a “log in” and “log out” entry to the Status File in the directory you 
configured.  No data is pushed with this command.  Connection data displayed on the terminal screen is 

useful if the connection fails. 

 

An immediate push of data can be done using the 

PUSHNOW

 command from the command prompt. 

 

 
TeleBoss 830 - FTP Settings 
A) FTP Push Enable                      [OFF] 
B) FTP Server Address                   [] 
C) Passive Mode                         [ON] 
D) Username                             [Default FTP Username] 
E) Password                             [********] 
F) Account                              [] 
G) Directory                            [] 
H) Minutes Between Push Attempts        [1440] 
I) Permissions                          [] 
J) Select Files to Push 
K) Remote File Names 
 

 

FTP Push Enable

  

FTP Push Enable toggles between OFF and REGULAR.  The default setting is OFF. 

 

FTP Server Address

  

Set this field as the IP address or host name of the FTP server to push to.  The maximum length is 64 

characters. 

 

Passive Mode 

This is an on off toggle to set the FTP Mode as Active or Passive.  The default is ON (Passive). 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands