Asentria TeleBoss 830 User Manual Download Page 33

Page: 33 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 33

Web Interface Control Features

The top section of the Web Interface display contains the type of Asentria Unit you have logged into, the

configured Site Name, the unit's factory assigned Serial Number and the software version loaded on this

TeleBoss. On the far right of the header you will see the user ID that you have logged in under and the

Logout button.

On the left side of the Web Interface display are navigation buttons. Clicking on

any of the "Status" options will bring up a status page displaying information

regarding the subject of the button. For example the "Sensors" button will bring

up a display that shows all of the installed EventSensors.

Most pages have sections

separated by a colored

bar. These sections are

collapsible. Double click

any bar and all sections

will collapse for ease of

handling long pages. A

single click will collapse or

expand any single section.

The buttons in the Settings Menu section will bring up a submenu of options under the subject heading listed.

Clicking on one of the submenu options will change the page display, bringing up the settings page for the

subject selected.

Settings Entry Functions

There are several different types of entry options for adjusting settings via the Web Interface.

Checkbox

Checkboxes are common for enabling and disabling settings. They are ON/OFF type options. A check

means ON. Click on the square to turn the option on or off.

Summary of Contents for TeleBoss 830






























































































































































Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands

Asentria TeleBoss 830, User Manual

Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands