manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 56

TeleBoss 830 2.11.370 STD User Manual     

 

Page 56 

 

 
TeleBoss 830 - IPRC Complex Multiline Record Settings 
A) Complex Multiline Record Enable      [OFF] 
B) Start Field 1 Character Position     [0] 
C) Start Field 1 Text                   [] 
D) Start Field 2 Character Position     [0] 
E) Start Field 2 Text                   [] 
F) Collect Lines Before Start Record    [0] 
G) End Detection                        [FORMULA] 
H) Line Count                           [0] 
I) End Field 1 Character Position       [0] 
J) End Field 1 Text                     [] 
K) End Field 2 Character Position       [0] 
L) End Field 2 Text                     [] 
 

 

Complex Multiline Record Enable

  

This is an ON/OFF toggle to enable advanced multiline detection.  The default setting is OFF. 

 

Start Field n Character Position

  

These two options set the character position used to define the beginning of the multiline field.  These options 

are used with "Count" method record end detection. 

 

Start Field n Text

  

Tjese two options set the text used to determine the beginning of the multiline field.  These options are used 

with "Formula" method record end detection. 

 

Collect Lines Before Start Record

  

This option sets the number of blank lines that are between each record. 

 

End Detection

  

This toggles between FORMULA, COUNT, and BLANKS to set the method of detecting the end of each 

record.  The default setting is FORMULA. 

 

Line Count

  

Line count is the number of lines to meter each record at. This option is used with "BLANKS" record end 

detection. 

 

End Field n Text/Character Position

  

These are the counterpart to start the text or character position options.  These sets the end delimiter for 

multiline records. 

 

 

NEC NEAX2400 

The TeleBoss collects data from the NEC NEAX2400 by opening a socket on a specific port. Generally, only 

the Hostname or IP Address of the switch is all that needs to be configured on the unit.  The Port number and 

Device number are settings on the TeleBoss that have the same default values as the corresponding settings 

in the switch.  

 

 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands