manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 19

TeleBoss 830 2.11.370 STD User Manual 

 

Page 19 

 

LEDs 

 

 

Each RJ45 port on the back panel has two LEDs associated with it 

– one on the Right of the port, one on the 

Left of the port. 

 

Ethernet Ports (ETH1 and ETH2) (and any additional Ethernet Ports that may be installed via an 

expansion card) 

●  Right – Lights solid red when an Ethernet cable is connected to the port and an active Ethernet 
network.  The LED is off when the cable is disconnected from the network, or the Ethernet Port. 
●  Left – Flashes yellow/green when network data (TCP packets) is being transmitted or received 
across the port.  When no data is actually being transmitted/received, this LED is off. 

 

I/O Port 1 & 2 (and any additional RS-232 serial port that may be installed via an expansion card) 

●  Right – Lights solid green when a correctly configured cable from another device is connected to 
it. Otherwise this LED remains off.  As the I/O Port receives or transmits data, this LED will flash red. 
●  Left – Lights solid green when power is applied to the T830, regardless of whether a cable is 
connected to the I/O Port or not. 

 

 

Ports 

Memory I/O 

The slot labeled Memory I/O can be used for the optional internal Temperature Sensor, which is a small MMC 

card. Firmware packages can also be flashed to the unit via this port under very specific conditions. 

 

Sensor 

The SensorJack port is a 9-pin Mini DIN connector for use with Asentria Type2 EventSensors.   

 

Ethernet 

The Ethernet 10/100Mb interfaces are standard RJ45.  Either of these standard connectors will connect the 

T830 to an Ethernet hub or switch.   

 

Serial Ports 

Each of the two (or more) serial ports is configured as a DTE port using an RJ45 connector.  This is the 

standard recommended pinout for EIA/TIA-561 for 8 pin RJ45 connector: 

 

PIN1 

= RI 

= RING INDICATOR, INPUT to the T830 

PIN2 

= DCD  = CARRIER DETECT, INPUT to the T830 

PIN3 

= DTR  = DATA TERMINAL READY, OUTPUT from the T830 

PIN4 

= SIGNAL GROUND 

PIN5 

= RXD  = RECEIVED DATA, INPUT to the T830 

PIN6 

= TXD  = TRANSMITTED DATA, OUTPUT from the T830 

PIN7 

= CTS  = CLEAR TO SEND, INPUT to the T830 

PIN8 

= RTS  = REQUEST TO SEND, OUTPUT from the T830 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands