manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 30

TeleBoss 830 2.11.370 STD User Manual     

 

Page 30 

 

 

After selecting an option, you are immediately returned to the previous menu.  The new value will be 

displayed to the right of the setting name, letter, or number. 

 

Alarm Actions (Action list) 

Alarm actions have their own unique method of entry.  Refer to the 

Actions List

 section for more information. 

 

 

Web Interface (GUI) 

The Web Interface is an intuitive GUI interface that can be used for routine control and maintenance of your 

TeleBoss via HTTP or HTTPS using up to date versions of Chrome, Firefox, or Internet Explorer.   

 

The TeleBoss has a built-in HTTP web server that can be used to configure the unit from anywhere the unit 

can be accessed on the network or Internet.  This interface is enabled by default.  Simply connect to 

http://<IP address of TeleBoss>

 or 

https://<IP address of TeleBoss>

 to use Secure Sockets Layer (SSL).   

 

Upon connection, you will be greeted by a login screen.  Log in with your Login ID (Username) and Password.  

These are the same credentials you would use to log into the command interface.  By default the user name is 

admin

 and the password is 

password

.  It is highly recommended that the password be changed via the User 

Profiles option from the Security menu. 

 

 

 

Once logged in, the Sensor Status screen will be displayed.  There is a menu tree on the left side of the 

display to configure and control the TeleBoss.  Using the menu tree you can alter most of the settings in the 

same way you could via the Command Line Interface. 

 

This interface can be disabled.  The configuration options for the Web Interface are located in the Web section 

of the Networking/Servers menu. If the Web Interface has been disabled it can be re-enabled at any time via 

the Command Interface 

SETUP

 menu at Network Settings/

Web Interface Settings

 menu.  

 

Commands and Serial Data cannot be entered or viewed via the Web Interface. 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands