manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 41

TeleBoss 830 2.11.370 STD User Manual 

 

Page 41 

 

 
TeleBoss 830 - Ethernet 1 Settings 
A) IPv4 Mode                            [STATIC] 
B) IP Address                           [0.0.0.0] 
C) Subnet Mask                          [255.255.255.0] 
D) Router Address                       [0.0.0.0] 
E) NAT                                  [ON] 
 

 

IPv4 Mode 

This setting toggles between STATIC, DHCP or VLAN and EXPANSION BRIDGE.  This should be set to 

whichever option is appropriate for this Ethernet port. The default setting is STATIC. 

 

The Ethernet Expansion Bridge feature bridges the onboard Ethernet interface to the Ethernet Expansion 

network interface. This feature requires at least one Ethernet Expansion card (E4 or 8E card) installed. 

 

IP Address

  

This option assigns the network address to this Ethernet port.  The default setting is 0.0.0.0 

 

Subnet Mask

  

This option is used to input the network subnet mask provided by the network administrator.  The default 

setting is 255.255.255.0 

 

Router Address

  

Set the router address provided by the network administrator using this option.  The default setting is 0.0.0.0 

 

NAT

  

This is an ON/OFF toggle to enable Network Address Translation.  The default setting is ON. 

 

Ethernet Settings as accessed via Web UI 

These same settings can be configured accessing the units Web GUI.  Navigate to Networking in the Settings 

Menu section of the right hand menu and select Network.  The drop-down menu in the grey Ethernet section 

bar toggles between Ethernet 1 and Ethernet 2 to allow separate configurations for each port.   

 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands