Asentria TeleBoss 830 User Manual Download Page 60

Page: 60 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 60

Enable EventSensor Reporting Host

This is

an ON/OFF toggle to enable this TeleBoss to be a host for EventSensor reporting from another

Asentria device. Default setting is OFF.

EventSensor Reporting Host Port

This is used

to set the TCP Port that this TeleBoss will use for receiving sensor reports from another Asentria

device. Default setting is 4000.

SNMP Settings

The SNMP Settings option displays a menu where you can enable the SNMP agent and configure community

names.

Testing SNMP Traps

Using the command interface enter the command

DOTRAP

from the command prompt. Verify that the trap

manager receives the test trap.

TeleBoss 830 - SNMP Settings
A) SNMP Agent Enable [OFF]
B) Read Community [public]
C) Write Community [public]
D) Trap Community [public]

SNMP Agent Enable

This option toggles between ON and OFF. It controls whether the unit responds to SNMP gets and sets. The

default setting is OFF.



Note

: SNMP Agent Enable does NOT stop SNMP traps from being sent when it is set to OFF.

Read / Write / Trap Community

These fields set the SNMP trap community names. The default setting for all is “public“. The maximum length
for each is 23 characters.



Note:

SNMP traps are

not

a guaranteed means of delivering notifications. Traps are a one-way IP

network datagram and the device receiving traps does not acknowledge them. Therefore, if the trap does

not reach its intended destination for whatever reason, the sending device has no way of recognizing this

and resending the trap.

SNMP Settings as accessed via Web UI

These same SNMP settings can be configured using the Web GUI, by navigating to Networking in the

Settings Menu and selecting SNMP.

There is no way to do a

DOTRAP

command test from the web interface.

Summary of Contents for TeleBoss 830






























































































































































Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands

Asentria TeleBoss 830, User Manual

Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands