Asentria TeleBoss 830 User Manual Download Page 63

Page: 63 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 63

Include Time in Filename

This is an ON/OFF toggle to enable the addition of the file transfer date and/or time to the beginning of the

name of each transferred file of data. The default setting is OFF.

Include Sequence #s in Filename

This is an ON/OFF toggle to enable the addition of a unique sequence number to the beginning of the name

of each transferred file of data. This ensures that no two transfers will have the same file name. The default

setting is OFF.

Data File n / Events File

These fields are text-entry fields where the name each data file will have on the remote server (not including

any date, time, or sequence numbers) can be configured.

FTP Settings as accessed via Web UI

These same FTP settings can be configured using the Web GUI, by navigating to Networking in the Settings

Menu and selecting FTP.

There is no way to do a

PUSHNOW

or a

PUSHTEST

command from the web interface.

PPP Settings

This option displays the PPP Settings menu for the internal dialup POTs modem. There are submenus where

you can configure settings for PPP Dialout, PPP Hosting, and Route Testing.

TeleBoss 830 - PPP Settings
A) PPP Dialout Settings
B) PPP Hosting Settings
C) Route Test Settings

Summary of Contents for TeleBoss 830






























































































































































Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands

Asentria TeleBoss 830, User Manual

Search results

Summary of Contents for TeleBoss 830

Reviews:

Brands by name

Popular brands