manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 11

TeleBoss 830 2.11.370 STD User Manual 

 

Page 11 

 

User 

User Name 

Password 

Login To 

User 1 

User1 

SMDR 

Command Interface or Web GUI 

User 2 

User2 

SUPER 

Command Interface or Web GUI 

User 3 

User3 

ACCESS1  

Pass-through/File 1 

User 4 

User4 

ACCESS2 

Pass-through/File 2 

User 11 

admin 

password 

Command Interface or Web GUI 

 

 

Access via a Serial Connection 

An alternate way to access your TeleBoss is using a serial port.  This will allow an immediate connection to 

the Command Line Interface of the TeleBoss.  The Serial Port labeled I/O2 is configured for command access 

by default.   

 

For a serial connection to a Console Port of a PC or laptop running any terminal emulator:  

 

USB Com port 

From a USB connection, a USB to RS232 DB9M adapter will be needed.  This is Asentria part no. 4161-021 or any 

commercially available adapter can be used.  

 

a.  Connect the USB adapter to a USB port on your computer. 

b.  Connect the DCE adapter (supplied with the TeleBoss) to the RS232 end of the adapter. 

c.  Use an RJ45 serial or Ethernet cable to connect the DCE adapter to the TeleBoss I/O2 port. 

 

 

 

Note:

 If both LEDs on the TeleBoss I/O2 port do not light, add the null adapter (supplied with the 

TeleBoss) between the adapters.

 

 

 

 

DB9 Interface Com Port 

a.  Connect the RJ-45 serial cable or a straight through Ethernet cable to the DTE adapter (supplied 

with the TeleBoss). 

b.  If your computer has a DB9 interface port, the DTE adapter can connect directly to a serial com 

port.   

c.  Connect the other end of the RJ-45 serial or Ethernet cable to the TeleBoss I/O2 serial port.  

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands