manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 151

TeleBoss 830 2.11.370 STD User Manual 

 

Page 151 

 

 
 

TELNET 

 
TELNET 
BusyBox v1.00 (2016.11.07-23:06+0000) multi-call binary 
 
Usage: telnet HOST [PORT] 
 
Telnet is used to establish interactive communication with another 
computer over a network using the TELNET protocol. 
 

 
 

TRACEROUTE 

 
TRACEROUTE 
Version 1.4a5 
Usage: traceroute [-dFInrvx] [-g gateway] [-i iface] [-f first_ttl] [-m max_ttl] 
        [ -p port] [-q nqueries] [-s src_addr] [-t tos] [-w waittime] 
        host [packetlen] 
 

 

VWB 

The 

VWB

 command presents low-level information about each sensor card installed on the system. This is 

mainly useful for analog inputs. The output looks something like this, depending on which cards are installed: 
 

 
>VWB 
-------- SLOT CONTENTS ------------------ 
--------------------- 
 
baseioCard[0]=ioSlot4 
   -------------- 
   Side A analog in 
   i00 z31608 p57099 n06117 r31963 v05000000     chan 0 =      69600uV 
   i03 z31502 p56886 n06118 r31628 v05000000     chan 1 =      24800uV 
   i06 z30800 p56311 n05289 r30914 v05000000     chan 2 =      22320uV 
   i09 z32649 p58027 n07271 r32714 v05000000     chan 3 =      12800uV 
   -------------- 
   Side B analog in 
   i00 z34035 p59343 n08727 r34040 v05000000     chan 0 =        960uV 
   i03 z31470 p56873 n06067 r31516 v05000000     chan 1 =       9040uV 
   i06 z32008 p57527 n06489 r32058 v05000000     chan 2 =       9760uV 
   i09 z30765 p56130 n05400 r30859 v05000000     chan 3 =      18480uV 
--------------------- 
 
baseioCard[1]=ioSlot5 
   -------------- 
   Side A Contact Closure 
   -------------- 
   Side B Contact Closure 
 
> 

 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands