manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 85

TeleBoss 830 2.11.370 STD User Manual 

 

Page 85 

 

 

 
TeleBoss 830 - Wireless Modem Advanced Settings 
A) Idle Timeout (minutes)               [0] 
B) Keep-Alive Threshold (minutes)       [0] 
C) PPP Debug Enable                     [OFF] 
D) Connectivity Check Settings          [OFF] 
 

 

Idle Timeout

  

Idle Timeout sets the number of minutes (0 

– 255) to wait before disconnecting an inactive modem 

connection.  A setting of 0 means the connection will not be terminated. The default setting is 0 minutes. 

 

Keep-Alive Threshold (minutes)  

This option sets the length of time, in minutes, after which the wireless modem will send an outbound 

packet to maintain a connection, if no data has been transmitted. A setting of 0 disables this feature. The 

default is 0. 

 

PPP Debug Enable

  

This is an ON/OFF toggle to enable capturing PPP traffic to a log file which can be extracted from the device 

and used for debugging purposes. The default setting is OFF. 

 

Connectivity Check Settings 

This option brings up a menu to set up the unit to check wireless connectivity.  The TeleBoss can be 

configured to ping up to two user-specified IP addresses at a user-specified interval.  If the count of 

consecutive failed tests reaches a user-specified threshold, and the modem is not in use, the TeleBoss will 

power cycle the wireless modem.  If the situation persists the TeleBoss will power cycle. 

 

The modem will not power cycle more often than every 10 minutes.  This interval increases on consecutive 

triggers to a maximum interval of 1 hour.  If resetting the modem does not restore connectivity, then the 

TeleBoss will be power cycled on the next trigger. The TeleBoss will not power cycle more often than every 12 

hours.  A system message is displayed in any open command processor saying that the system is going to 

reboot in 30 seconds. 

 

 
TeleBoss 830 - Connectivity Check Settings 
A) Enable                               [OFF] 
B) IP Address 1                         [0.0.0.0] 
C) IP Address 2                         [0.0.0.0] 
D) IP Address 3                         [0.0.0.0] 
E) Check Interval (minutes)             [2] 
F) Fail Threshold                       [5] 
G) RX Reset                             [ON] 
 

 

Enable 

This is an ON/OFF toggle to enable or disable the feature. Default is OFF. 

 

IP Address n

 

Use these fields to set the IP address(es) that will be pinged for the connectivity check. The default is 0.0.0.0, 

note the unit will not ping 0.0.0.0.   

 

Check Interval (minutes) 

This field is used to set how often the IP address(es) will be pinged, in minutes. Range is 1 to 10 minutes. The 

default is 2. 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands