manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 122

TeleBoss 830 2.11.370 STD User Manual     

 

Page 122 

 

Action Settings as accessed via Web UI 

The Actions Settings and the Action Schedule are located at the top of the General Actions page.  The 

General Actions page is under the Events tab in the Settings Menu section of the GUI. 

 

 

 

 

General Settings 

The General Settings menu is where you can set the site name, answer string, confirmation prompt, 

date/time, and other general settings.   

 

 
TeleBoss 830 - General Settings 
A) Site Name                            [830-830000163] 
B) Answer String                        [TeleBoss] 
C) Escape Key                           [27] 
D) Confirmation Prompt                  [ON] 
E) Time Stamp Format                    [HH:MM] 
F) Date Stamp Format                    [MM/DD] 
G) Space After Date/Time Stamp          [ON] 
H) Prompt                               [] 
I) Date/Time Setup 
J) Legacy Settings 
K) Joinable Pass-through                [ON] 
 

 

Site Name

  

This is a text string to set the name assigned to this TeleBoss.  This name is included with alarm messages 

(Traps, Emails, etc.) and is displayed at the top of the Status screen.  The name should be unique for clarity.  

The maximum length is 40 characters.  The d

efault setting is “830 - <

serial number

>” 

 

Answer String

 sets the string that is presented when a user connects to the T830 via Telnet or modem.  (Max 

length 31 chars) 

 

Escape Key

 is the decimal ASCII character code of the key you must press three times to escape from 

passthrough or other transparent modes.  Default is 27, the <ESC> key. 

 

Confirmation Prompt

 is an ON/OFF toggle to set whether a confirmation prompt (

Are you sure (y/n)?

) 

is displayed when the commands 

COLDSTART, DEFAULT, DEFAULT ALL, 

and 

ZERO

 

are issued, and 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands