manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 105

TeleBoss 830 2.11.370 STD User Manual 

 

Page 105 

 

Actions

  

This selection will display the 

Actions List

, a menu where the action string for the event is configured.  This 

field will be empty  [ ] if no actions have been configured, and will show [*SET*] if one or more actions have 

been configured. 

 

Class

  

This option is used to set the class for the alarm.  When this option is selected, a list of the classes previously 

defined in the 

Class Table

 is displayed, from which you can select one to be assigned to this data alarm.  The 

default is Info. 

 

Data Alarm Trap Number

  

This field sets the number to be sent with any SNMP traps for this event.  Default is 503, but trap number can 

also be set in the range of 1000 

– 1199 as needed. 

 

Clear This Alarm Counter Now  

This option

 

allows you to clear the counter for the selected data alarm manually.  This happens as soon as 

this option is selected, so make sure you really want to clear the counter before selecting it. 

 

 

Data Alarm/Filter n Settings as accessed via Web UI 

The Data Alarm/Filter 

n

 

Settings can be 

configured via the Web 

Interface.  They can be 

access from the Events 

tab on the Data 

Alarm/Filters page. From 

the Alarm/Filter Overview 

section, clicking the blue 

hyper link numbered 
options under “Name” will 
bring up the individual 

Alarm/Filter 

n 

fields to 

configure in the lower 

section of the page.  U

se

 

the drop down in the grey 

bar to bring up addional 

Alarm/Filter 

n

 options to 

configure.  

 
The “Clear” buttons on the far right side in the Alarm/Filter Overview section is the “Clear This Alarm Counter 
Now” button.  Clicking the button will clear the counter for that data alarm filter. 
 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands