manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 90

TeleBoss 830 2.11.370 STD User Manual     

 

Page 90 

 

 

Passthrough

 

 
TeleBoss 
Password: ******** 
Connected to I/O 1 
 

 

File Access Pointer

 toggles through each of the data files on the unit (FILE1, FILE2, etc) to set what data file 

the user has access to when logging in to the command processor. 

 

Set Pass-through Pointer To  

This option toggles through the available serial ports and 

specifies the destination if the “Upon Login then Go 

To” action is set to Pass-Through.  Whatever this option is set for determines where this user will be routed to 
on a pass-through connection.  Default setting is FILE1.

 

 

Pass-through Permissions  

This option is in effect if the “Upon Login then Go To” action is set to Menu. This option displays a menu 
showing all serial ports which can be toggled between ALLOW or DENY.  If a port is set as ALLOW, then that 

serial port is displayed in the Menu after the user logs in.  If a port is set as DENY, then that serial port is not 

displayed in the Menu.  The default setting for all ports is ALLOW. 

 

After PT, ESC Takes User To  

This toggles between MENU and DISCONNECT to set where the user is sent when they exit out of a pass-

through connection.  The default is MENU.

 

 

PPP Connection  

This option toggles between LOCAL and NONE.  LOCAL allows PPP access, but denies all routing to 

whatever LAN the TeleBoss is connected to.  NONE disables PPP access for the user. 

  

Setup / Status Rights  

This selection toggles through the actions available to the user.  The Options are MASTER, NONE, VIEW, 

ADMIN1, ADMIN2, and ADMIN3.  See the 

User Profiles Feature Guide 

 on the Asentria Information Portal for 

more information on each access level.    The default setting is MASTER.

 

 

File Release / Delete Permissions  

These options set this user’s permissions level to transfer or delete data stored in the units files.  Selecting a 
File option will display a menu showing all data files as well as the Events Log and Audit Log.  Selecting one 

of these options toggles the setting between ALLOW and DENY.  The default setting for all is ALLOW. 

 

 

User Profile Security Settings as accessed via Web UI  

To access the User Profiles settings options on the Web Interface click on the Security option on the left hand 

menu and select User Profiles.  At the top of the page is a Status section.  To modify the settings for any 

specific user click on the blue hyper link associated with that user. 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands