manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 146

TeleBoss 830 2.11.370 STD User Manual     

 

Page 146 

 

COMPRESS 

Release compressed 

records 

COMPRESS [ON\OFF] 

When ON, releases records in compressed format 

where spaces are replaced by an alpha character; 

when OFF, released records exactly as received. 

ESC/ESC/ESC 

Escape command 

ESC/ESC/ESC 

Stops the release of data.  If used when releasing 

data in LINE mode, records not yet displayed are 

still considered released and will be deleted when 

the CLEAR command is issued. 

NEXT 

Sends the next 

record or block of 

records 

NEXT 

When WAIT is ON, the NEXT command causes 

records to be released according to the previously 

issued RELEASE command. 

PRT

 

Set data partition  

PRT 

Sets a partition to separate existing data in a file 

from any new data 

RL

 

Release data 

RL  

RLn 

RL@nnn 

RLn@nnn 

Releases the data stored in a data file.  RL release 

all data in the partition; RL

n

 releases just 

n

 number 

of records; RL@

nnn

 release all records beginning a 

record number 

nnn

; RL

n

@

nnn

 release 

n

 number of 

records beginning at record number 

nnn

. 

RLMODE 

Set the release mode 

RLMODE 

RLMODE LINE 

RLMODE CBB 

RLMODE XMODEM 

By itself, RLMODE displays what the current 

release mode is.  Followed by LINE, CBB, or 

XMODEM, it sets the RLMODE to one of those 

methods. 

TAG 

Prepend a line 

number to records 

TAG [ON|OFF] 

By itself, TAG displays the current setting. When set 

to ON, TAG will prepend a six-digit line number 

(beginning with 000001) to call records as they are 

released. 

TRIM 

Delete records in a 

data file. 

TRIM 

n

 

TRIM followed by a number of records will delete 

that many records from the beginning of a data file, 

whether they have been released already or not.  To 

delete the entire file, enter TRIM followed by a 

number that is greater than the number of records in 

the file. 

WAIT 

Sets the “wait for 
next” mode 

WAIT [ON|OFF] 

By itself, WAIT displays what the current wait mode 

is.  When set to ON, data release will not start after 
the RL command is given, but instead will “wait” 
until the NEXT command is sent. 

ZERO 

Deletes records from 

all data files. 

ZERO 

After issuing this command, the user is prompted 
with “Are you sure (y/n)?”.  Selecting “y” will delete 
all data in all data files (including the Audit and 

Event logs).  

 

 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands