manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 132

TeleBoss 830 2.11.370 STD User Manual     

 

Page 132 

 

Dialup Pager  

Send a pager callout via Dialup POTs modem to a number specified by index number, which can be 

configured in the Actions Settings/

Pager

 section. 

 

DPAGE(INDEX) 

 

Dispatcher  

Send a Dispatcher alarm via a Dialup POTs modem to a number specified by index number, which can be 

configured in the Action Definitions menu/

Phone Number

 section. 

 

DISPATCH(PHONE# 

or 

INDEX#)

 

 

Email  

Send an email notification to an address specified by index number which can be configured in Action 

Definitions menu 

Email Address

 section or delineated in the action.

 

 

EMAIL(EMAIL 

or

 INDEX#) 

 

Group 

Group is used to identify this action list as part of a group identified by group name, not currently used. 

 

GROUP(GROUPNAME)

 

 

ID 

Identify this action by a descriptor, for reference in other action. 

 

ID(IDNAME) 

 

Malert  

Malert sends a malert (Asentria Alarm via modem) to a number specified by index number, which can be 

configured in the Action Definitions menu/

Phone Number

 section. 

 

MALERT(PHONE# 

or 

INDEX#) 

 

Modem  

Make the unit dial a phone number via the POTs modem to a specified index number, which can be 

configured in the Action Definitions menu/

Phone Number

 section, and start a login session (to the unit's 

command processor) with the answering machine. 

 

MODEM(PHONE# 

or 

INDEX#)  

 

Pause  

Pause operation for a duration specified by seconds. 

 

PAUSE(SECONDS) 

 

Postpone  

Postpone an already-running action identified by 

ID

 for a duration specified by seconds. 

 

POSTPONE(IDNAME, SECONDS) 

 

Power 

Using this action puts a power output into a defined state, determined by the action parameter. 

 

Action:

 one of the following two words, by case-insensitive exact match: 

ON

 or 

OFF 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands