manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 83

TeleBoss 830 2.11.370 STD User Manual 

 

Page 83 

 

 

Note:

 

If Duplex is set to Half, set 

sys.terminal.mode

=OFF

.  Otherwise, characters will continue to be 

echoed to the terminal screen. 

 

Init String

  

This option sets the user-defined modem initialization string.  This string is sent to the modem before 

important factory modem initialization settings, so certain settings in this init string may be overridden.  The 

default setting is ATM1.  The maximum length is 126 characters.    

 

 

Note:

  Make sure to enter 'AT' at the beginning of this initialization string. 

 

Inactivity Timeout

  

This selection sets the number of minutes (0 

– 255) to wait before disconnecting an idle modem connection.  

A setting of 0 means the connection will never automatically expire.  The default setting is 0. 

 

Upon Modem Connect Go Directly To

  

This menu option toggles through a list of actions to control what a user sees directly after connecting via 

modem.  LOGIN requires the user to login with username and password, and will then take them to a 

command prompt.  A serial port (I/O1, I/O2, etc.) redirects a modem user directly to that serial port upon 

connecting.  In this passthrough mode, the command processor of the TeleBoss is transparent.  The default 

setting is LOGIN. 

 

TAP Init String

  

This option is the user-defined modem initialization string used only when the modem is making an 

alphanumeric modem callout.  Default setting is ATM0.  The maximum length is 126 characters      

 

 

Note: 

 Make sure to enter 'AT' at the beginning of this initialization string. 

 

TAP Uses 8N1 Data/Parity/Stop  

This option toggles between 1, to force the TAP initialization string data/parity/stop settings to 8N1, and 0 to 

not force this setting.  Default setting is 0. 

 

Setting Key:

  

modem.hsk 

Values are 

RTS

 (default), 

None

 and 

Xon

.  RTS means that on serial pass-through, the modem uses RTS 

handshaking; None means no handshaking is used; and Xon means XON/XOFF characters are used. 

 

 

Dialup Modem Settings as accessed via Web UI  

These settings can be set up on the Web Interface.  They would be accessed from the Dialup Modem 

submenu under the Communication option from the left hand menu. 

  

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands