manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 74

TeleBoss 830 2.11.370 STD User Manual     

 

Page 74 

 

 

 

Transfer VPN 1 Certificate 

Use the Choose File button to select the client or server certificate text file (client.crt) and then click the 

Upload button to load it onto the TeleBoss. 

 

Transfer VPN 1 Key 

Use the Choose File button to select the key file (client.key) and then click the Upload button to load it onto 

the TeleBoss. 

 

Transfer CA 1 Certificate  

Use the Choose File button to select the CA certificate text file (ca.crt) and then click the Upload button to load 

it onto the TeleBoss. 

 

Transfer TLS 1 Key 

Use this option to load the TLS Authority key. If the server uses this, then the unit must use this too. Use the 

Choose File button to select the file and then click the Upload button to load it onto the TeleBoss. 

 

Transfer DH1 Parameters 

Use the Choose File button to select the DH1 Parameters text file, if this functionality is being used on your 

VPN, and then click the Upload button to load it onto the TeleBoss. 

 

 

CPE Settings  

The CPE Settings menu is where up to 64 different the Customer Premises Equipment (CPE) devices can be 

configured for keep-alive monitoring by the TeleBoss.   

 

Activate the Alarm functions in the Alarm/Event Definitions/

CPE Alarm Settings

.   Once the devices are 

configured in this menu and the CPE Alarm Settings are enabled the status of the devices configured for 

monitoring can be viewed from the command line by typing 

?CPE

 at the command prompt.  Contact 

Asentria 

Technical Support

 for further information. 

 

 

 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands