manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 44

TeleBoss 830 2.11.370 STD User Manual     

 

Page 44 

 

Data Alarm/Filter Enable 

This is an ON/OFF toggle to set whether configured Data Alarms or Filters will be applied to the incoming 

data.  The default setting is OFF. 

 

Target Name 

This is a text field to name the switch and is used in the alarm messages.  The default name is IPRC 1. 

 

Port 

This field is used to define the listening port of the switch.  The default is 5000 for a generic server and 9000 

for an Avaya DRP device.  This port number must match the remote TCP port configured for on the PBX or 

Sever. 

 

Time Stamping 

This is an ON/OFF toggle to set whether each individual call record is stamped with the Date and Time 

received in the TeleBoss.  The default setting is OFF. 

 

 

Alcatel OmniPCX 

This PBX has been upgraded many times and is now Alcatel OXE but the means of querying the CDR is still 

the same.  These PBXs function by doing a real-time SQL-query of specific fields that you must define. Each 

field will be delimited by a comma or space or any ASCII character you choose. You also must define the 

number of spaces each field will be. This is very important if you plan on performing data alarming on the call 

data. 

 

 
TeleBoss 830 - IP Record Collection (IPRC) Setup 
A) IP Record Collection                 [ALCATEL OMNIPCX] 
B) Store Collected Data In              [FILE1] 
C) Data Alarm/Filter Enable             [OFF] 
D) Target Name                          [IPRC 1] 
E) Hostname/IP Address                  [] 
F) Port                                 [2533] 
G) Timeout (seconds)                    [30] 
H) Delimiter                            [00] 
I) Field Setup 
 

 

IP Record Collection 

This option is used to select the IP Record Collection protocol.  Setting this to something other than OFF 

enables IP Record Collection and displayes the settings needed for that protocol. 

 

Store Collected Data In 

This field sets

 the data file in which to store records received via IPRC.  The default setting is FILE1. 

 

Data Alarm/Filter Enable 

This is an ON/OFF toggle to set whether configured Data Alarms or Filters will be applied to the incoming 

data.  The default setting is OFF. 

 

Target Name 

This is a text field to name the switch and is used in the alarm messages.  The default name is IPRC 1. 

 

Hostname/IP Address 

This field is used to set the IP address or Hostname of the Alcatel Server.   

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands