manualshive.com logo in svg

ARTERY AT32WB415 Series, Reference Manual

The ARTERY AT32WB415 Series is a cutting-edge electronic device that revolutionizes connectivity. To learn more about its features and specifications, make sure to download the free Reference Manual from our website. This manual provides step-by-step instructions on how to maximize the performance of your ARTERY device.

Share
Download
background image

  AT32WB415

 

Series  Reference  Manual

 

2022.04.13

 

Page 54 

 

Ver 2.00

 

Bit 1 

LEXTSTBLF 

0x0 

ro 

LEXT stable flag 
Set by hardware. 
0: LEXT is not ready. 
1: LEXT is ready. 

Bit 0 

LICKSTBLF 

0x0 

ro 

LICK stable interrupt flag 
Set by hardware. 
0: LICK is not ready. 
1: LICK is ready. 

4.3.4 

APB2 peripheral reset register (CRM_APB2RST) 

Access: 0 wait state, accessible by words, half-words and bytes. 

Bit 

Name 

Reset value 

Type 

Description 

Bit 31: 22  Reserved 

0x000 

resd 

Kept at its default value. 

Bit 21 

Reserved 

0x0 

resd 

TMR17 reset 
0: Does not reset TMR17 
1: Reset TMR17 

Bit 20   

TMR10ST 

0x0 

rw 

TMR10 set 
0: Does not reset TMR16 
1: Reset TMR16 

Bit 19 

TMR9ST 

0x0 

rw 

TMR9reset 
0: Does not reset TMR15 
1: Reset TMR15 

Bit 18: 15  Reserved 

0x0 

resd 

Kept at its default value. 

Bit 14 

USART1RST 

0x0 

rw 

USART1 reset 
0: Does not reset USART1 
1: Reset USART1 

Bit 13 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 12 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 11 

TMR1RST 

0x0 

rw 

TMR1 reset 
0: Does not reset TMR1 
1: Reset TMR1 

Bit 10 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 9 

ADC1RST 

0x0 

rw 

ADC1 reset 
0: Does not reset ADC1 
1: Reset ADC1 

Bit 8 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 7 

GPIOFRST 

0x0 

rw 

GPIOF reset 
0: Does not reset GPIOF 
1: Reset GPIOF 

Bit 6 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 5 

GPIODRST 

0x0 

rw 

GPIOD reset 
0: Does not reset GPIOD 
1: Reset GPIOD 

Bit 4 

GPIOCRST 

0x0 

rw 

GPIOC reset 
0: Does not reset GPIOC 
1: Reset GPIOC 

Bit 3 

GPIOBRST 

0x0 

rw 

GPIOB reset 
0: Does not reset GPIOB 
1: Reset GPIOB 

Bit 2 

GPIOARST 

0x0 

rw 

GPIOA reset 
0: Does not reset GPIOA 
1: Reset GPIOA 

Bit 1 

EXINTRST 

0x0 

rw 

EXINT reset 
0: Does not reset EXINT 
1: Reset EXINT 

Bit 0 

IOMUXRST 

0 

rw 

IOMUX reset 
0: Does not reset IOMUX 
1: Reset IOMUX 

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32WB415 Series

Daavlin 7 Series Operation Manual preview
7 Series
Brand: Daavlin Pages: 13
Daavlin 7 Series Operating Instructions Manual preview
7 Series
Brand: Daavlin Pages: 27
NEC MD462OR Quick Reference Manual preview
MD462OR
Brand: NEC Pages: 44
T-Rex BIG FOOT User Manual preview
BIG FOOT
Brand: T-Rex Pages: 13
Parker SC80 Operator'S Manual preview
SC80
Brand: Parker Pages: 39
T&D TR-73U User Manual preview
TR-73U
Brand: T&D Pages: 28
KaVo INTRAmatic 31 ES Instructions For Use Manual preview
INTRAmatic 31 ES
Brand: KaVo Pages: 52
Marani DPA360P User Manual preview
DPA360P
Brand: Marani Pages: 35
My-Doc DocLaser Sport Quick Reference Manual preview
DocLaser Sport
Brand: My-Doc Pages: 32
Spitzer LIGHTING DSKL10-18WCC-S Installation Manual preview
DSKL10-18WCC-S
Brand: Spitzer LIGHTING Pages: 2
Cameo CLMFXBAR User Manual preview
CLMFXBAR
Brand: Cameo Pages: 56
Nano Temper Monolith NT.115 User Manual preview
Monolith NT.115
Brand: Nano Temper Pages: 24
MetalTech SCAFFOLDBENCH I-CISRL Operational Safety And Assembly Instructions preview
SCAFFOLDBENCH I-CISRL
Brand: MetalTech Pages: 16
Kurzweil MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE Manual preview
MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE
Brand: Kurzweil Pages: 91
schmersal SLC440 Operating Instructions Manual preview
SLC440
Brand: schmersal Pages: 20
Exalto 2178.085 Manual preview
2178.085
Brand: Exalto Pages: 28
PURE 8533HT Owner'S Manual preview
8533HT
Brand: PURE Pages: 16
POOL LAB 55619 Manual preview
55619
Brand: POOL LAB Pages: 6

Brands by name

Popular brands

Load more brands