manualshive.com logo in svg

ARTERY AT32WB415 Series, Reference Manual

The ARTERY AT32WB415 Series is a cutting-edge electronic device that revolutionizes connectivity. To learn more about its features and specifications, make sure to download the free Reference Manual from our website. This manual provides step-by-step instructions on how to maximize the performance of your ARTERY device.

Share
Download
background image

  AT32WB415

 

Series  Reference  Manual

 

2022.04.13

 

Page 346 

 

Ver 2.00

 

the port into test mode, and the port gives a corresponding 
signal. 
0000: Test mode disabled 
0001: Test_J mode 
0010: Test_K mode 
0011: Test_SE0_NAK mode 
0100: Test_Packet mode 
0101: Test_Force_Enable 
Others: Reserved 

Bit 12 

PRTPWR 

0x0 

rw 

Port power 
The application uses this bit to control power supply to this 
port (by writing 1 or 0) 
0: Power off 
1: Power on 
Note:  This  bit  is  not  associated  with  interfaces.  The 
application must follow the programming manual to set this 
bit for various interfaces. 

Bit 11: 10  PRTLNSTS 

0x0 

ro 

Port line status 
Indicates the current logic status of the USB data lines. 
Bit [10]: Logic level of D+ 
Bit [11]: Logic level of D– 

Bit 9 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 8 

PRTRST 

0x0 

rw 

Port reset 
When this bit is set by the application, a reset sequence is 
started on this port. The application must calculate the time 
required for the reset sequence, and clear this bit after the 
reset sequence is complete. 
0: Port not in reset 
1: Port in reset 
The  application  must  keep  this  bit  set  for  a  minimum 
duration defined in Section 7.1.7.5 of USB 2.0 specification 
to  start  a  reset  on  the  port.  In  addition  to  this,  the 
application can make this bit set for another 10 ms to the 
minimum  duration,  before  clearing  this  bit.  There  is  no 
maximum limit set by the USB standard. 

Bit 7 

PRTSUSP 

0x0 

rw1s 

Port suspend 
The  application  sets  this  bit  to  put  this  port  in  suspend 
mode. In this case, the controller only stops sending SOF. 
The application must set the port clock stop bit in order to 
disable the PHY clock. 
The  read  value  of  this  bit  reflects  the  current  suspend 
status of the port. 
This bit is cleared by the controller when a remote wakeup 
signal  is  detected  or  when  the  application  sets  the  port 
reset  bit  or  port  resume  bit  in  this  register,  or  sets  the 
resume/remote  wakeup  detected  interrupt  bit  or 
disconnect detected interrupt bit in the controller interrupt 
register. 
The controller can still clear this bit, even if the device is 
disconnected with the host. 
0: Port not in suspend mode 
1: Port in suspend mode 

Bit 6 

PRTRES 

0x0 

rw 

Port resume 
The application sets this bit to drive resume signaling on 
the  port.  The  controller  continues  to  trigger  the  resume 
signal until the application clears this bit. If the controller 
detects a USB remote wakeup sequence (as indicated by 
the  port  resume/remote  wakeup  detected  interrupt  bit  of 
the controller interrupt register), the controller starts driving 
resume  signaling  without  the  intervention  of  the 
application. 
The read value of this bit indicates wehter the controller is 
currently driving resume signaling.   
0: No resume triggered 
1: Resume triggered 

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32WB415 Series

NEC MD462OR Quick Reference Manual preview
MD462OR
Brand: NEC Pages: 44
YATEK ECO Owner'S Manual preview
ECO
Brand: YATEK Pages: 72
Eaton PowerXL DX-NET-ETHERNET2-2 User Manual preview
PowerXL DX-NET-ETHERNET2-2
Brand: Eaton Pages: 48
Eaton Power Xpert C445 Manual preview
Power Xpert C445
Brand: Eaton Pages: 2
EAW UX8800 Quick Start Manual preview
UX8800
Brand: EAW Pages: 2
abc 907 Instructions For Use Manual preview
907
Brand: abc Pages: 28
Hach MET ONE 3400 Series User Manual preview
MET ONE 3400 Series
Brand: Hach Pages: 48
Jaga OXRE.015 Service Manual preview
OXRE.015
Brand: Jaga Pages: 32
Varytec Derby User Manual preview
Derby
Brand: Varytec Pages: 5
Saab R60 User Manual preview
R60
Brand: Saab Pages: 98
Kaixin DCU10 User Manual preview
DCU10
Brand: Kaixin Pages: 89
laerdal SimPad Quick Start Manual preview
SimPad
Brand: laerdal Pages: 9
Nasco Life/form SmartScope LF01142U User Help Manual preview
Life/form SmartScope LF01142U
Brand: Nasco Pages: 2
Uchida Yoko BC-10 Service Manual preview
BC-10
Brand: Uchida Yoko Pages: 40
U-Line S-11303 Quick Start Manual preview
S-11303
Brand: U-Line Pages: 3
U-Line H-3736 Installation Instructions preview
H-3736
Brand: U-Line Pages: 2
YASKAWA GA500 series Installation And Operation Instruction Manual preview
GA500 series
Brand: YASKAWA Pages: 81
YASKAWA Varispeed f7 User Manual preview
Varispeed f7
Brand: YASKAWA Pages: 52

Brands by name

Popular brands

Load more brands