ARTERY AT32WB415 Series Reference Manual Download Page 342 | Manualshive

Page: 342 / 374

background image

AT32WB415

Series Reference Manual

2022.04.13

Page 342

Ver 2.00

20.6.3.12

OTGFS general controller configuration register

(OTGFS_GCCFG)

Bit

Register

Reset value

Type

Description

Bit 31: 22 Reserved

0x000

resd

Kept at its default value.

Bit 21

VBUSIG

0x0

rw

VBUS ignored
When this bit is set, the OTGFS controller does not monitor
the Vbus pin voltage, and assumes that the Vbus is always
active in both host and device modes, and leaves the Vbus
pin for other purposes.
0: Vbus is not ignored
1: Vbus is ignored, and is deemed as always active

Bit 20

SOFOUTEN

0x0

rw

SOF output enable
0: No SOF pulse output
1: SOF pulse output on PIN

Bit 19

BVALIDSESEN

0x0

rw

Bvalid sense enable
0: Disabled
1: Enabled

Bit 18

AVALIDSESEN

0x0

rw

Avalid sense enable
0: Disabled
1: Enabled

Bit 17

Reserved

0x0

resd

Kept at its default value.

Bit 16

PWRDOWN

0x0

rw

Power down
This bit is used to activate the transceiver in
transmission/reception. It must be pre-configured to allow
USB communication.
0: Power down enable
1: Power down disable (Transceiver active)

Bit 15: 0

Reserved

0x0000

resd

Kept at its default value.

20.6.3.13

OTGFS controller ID register (OTGFS_GUID)

This is a read-only register containg the production ID.

Bit

Register

Reset value

Type

Description

31: 0

USERID

0x0000 1000 rw

Product ID field
The application can program the ID field.

20.6.3.14

OTGFS host periodic Tx FIFO size register

(OTGFS_HPTXFSIZ)

This register contains the size and memory start address of the periodic transmit FIFO.

Bit

Register

Reset value

Type

Description

Bit 31: 16 PTXFSIZE

0x02000

ro/rw

Host periodic TxFIFO depth
Values are in terms of 32-bit words.
Minimum value is 16
Maximum value is 512

Bit 15: 0

PTXFSTADDR

0x0600

ro/rw

Host Periodic TxFIFO start address
The power-on reset value of this register is the sum of the
largest receive FIFO depth and the largest non-periodic
transmit FIFO depth.

«
...
340
341
342
343
344
...
»

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32WB415 Series

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: ACE INSTRUMENTS Pages: 2

Brand: ODA Pages: 103

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: Uchida Yoko Pages: 40

Brand: Yamaha Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands