manualshive.com logo in svg

Anritsu MX183000A, Operation Manual, Page: 9 / 226

Share
Download
Anritsu MX183000A Operation Manual Download Page 9

 

ix 

 

 

 
 

Protection Against Computer Virus Infections 

Prior to the software installation 
Before installing this software or any other software recommended or 
approved by Anritsu, run  a virus scan on your computer, including 
removable media (e.g. USB memory stick and CF memory card) you 
want to connect to your computer. 
 
When using this software and connecting with the measuring instrument 

•

  Copying files and data 

On your computer, do not save any copies other than the following: 

 

•

 Files and data provided by Anritsu 

 

•

 Files created by this software 

 

•

 Files specified in this document 

Before copying these files and/or data, run a virus  scan, including 
removable media (e.g. USB memory stick and CF memory card). 

•

  Connecting to network 

Connect your computer to the network that provides adequate 
protection against computer viruses. 

 
 
 

Cautions on Proper Operation of Software 

This software may not operate normally if any of the following operations 
are performed on your computer: 

•

  Simultaneously running any software other than that recommended or 

approved by Anritsu 

•

  Closing the lid (Laptop computer) 

•

  Turning on the screen saver function 

•

  Turning on the battery-power saving function (Laptop computer) 

For how to turn off the functions, refer to the operation manual that came 
with your computer. 

 
 
 

Summary of Contents for MX183000A



































































































































































































































Reviews:

No comments