manualshive.com logo in svg

Anritsu MX183000A, Operation Manual, Page: 79 / 226

Share
Download
Anritsu MX183000A Operation Manual Download Page 79

 

4.5  USB Link Sequence 

4-25 

4 

 

O

per

ation
 

 

4.5.3 USB Link Sequence Start 

 

 

Figure 4.5.3-1  USB Link Sequence Transmission Procedure 

 
When [Sequence Start] is clicked, PPG is in the wait status for receiving 
the LFPS signal and the button display is changed to Stop.   
Connect the USB Test Fixture connector to DUT in this condition. 
DUT detects the connection of the USB connector and outputs the LFPS 
signal.   
PPG receives the LFPS signal output from DUT at AUX Input and starts 
the link training sequence.   
When the link training sequence transmission is completed, the button 
display is changed to Unlink and the test pattern is sent from PPG.   

Start 

When PPG detects the LFPS 

signal, the sequence 

transmission is started.   

Check that the button display is 

changed to [Unlink].   

BER measurement   

 

Check that the button display is 

changed to [Stop] and PPG is 

in the wait status for receiving 

the LFPS signal.   

Connect the USB Test Fixture 

to DUT. In this case, DUT 

detects the connection and 

outputs the LFPS signal.   

Select the USB3.1 

Specification from Gen1 or 

Gen2. 

Select [Not Wait For The LFPS 

Signal].   

Click [Sequence Start].   

Yes 

No 

PPG starts the sequence.   

Check that the button display is 

changed to [Unlink].   

Summary of Contents for MX183000A



































































































































































































































Reviews:

No comments