manualshive.com logo in svg

AccuEnergy AXM-WEB2, User Manual, Page: 115 / 131

Share
Download
AccuEnergy AXM-WEB2 User Manual Download Page 115

www.accuenergy.com

V: 1.10  Revised: January 2020

113

Chapter 10:  Web Interface Readings and Parameter Settings

10.6.5 Module Firmware Update

The Module Firmware web page is used for updating the firmware version on the AXM-WEB2 

module. The user can check if the module they are using is up to date and update the module 

if needed using the remoter firmware update.  Users can also manually update the firmware by 
uploading the firmware file.  The current version of the firmware will be displayed on the Mod

-

ule firmware update page and can also be viewed on the 'Device Information' page of the web 

interface.  

There is an Auto Firmware Update feature available also, this allows users to update the module 
automatically without manually going into the web server and performing the update.  

NOTE:

 Users can also contact Accuenergy Technical Support for latest firmware. 

Auto Firmware Update

The auto firmware update allows users to select three different updating options.

• 

Disable - Disables the auto firmware update function

• 

Critical Update Only - Updates the module to the latest critical firmware

• 

Automatically keep firmware to Latest - Updates the module to the latest firmware

If users select critical or latest firmware update options, the time for the update can be config

-

ured.  By default the update time is set for 3am-4am.  

NOTE: 

The one hour time block means that the update will occur anytime within the hour.

Summary of Contents for AXM-WEB2




































































































































Reviews:

No comments