Zontes ZT350-EURO V 2022, Руководство по обслуживанию

Страница: 64 / 118

8-FRONT FORK COMPONENT
63
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1 1250205-023000 GB70.1 inner hexagonal M8×35 (color Zinc) 4 20N.m
2 1094100-063000 ZT650 front wheel hollow shaft Φ20×243 1
4 1274300-007000 ZT350-GK ABS induction ring gear (60 teeth) 1
5 1100100-783000 ZT350-GK front brake disc (320×5.0) 1
6 1251100-117093 Non-standard inner hex bolt M8×25 5
7 1250402-001091 GB12615φ3×10 5
8 1094100-037000 ZT250-R front wheel right fixed bushing 1
9 1184300-034000 ZT350 tire pressure sensor (M8 straight head) 1
11 1230100-558000 120/70ZR17 CM
－
S3 58W TL E4 1
●
Maintenance project tires: regular check whether the tires have cracks, cracks, air pressure, etc.If it has
been worn to the tire wear identification, it must be replaced with tires of the same specifications.
Refer to the instructions in detail. Tire is not suitable for areas with low temperature. When the outdoor
temperature is too low, it is recommended to store the vehicle in a high temperature place or indoors to
prevent frozen cracks. Normal temperature: Standard 280kPa. Wheels: Check whether the wheels have
adverse phenomena such as deformation and cracks. Support the rotation of the rotation level to check
whether there are stagnation, swinging, etc.
Rotal oil seal: TCφ42 × φ28 × 7; bearing: size φ42 × φ20 × 12, specifications: 6004-2RS.
Wheel axis: Use a percentage table to check whether there is deformation and bending.
Braking disk: After the brake disk is replaced, it should be fully running in before the brake disk is fully
run into the best brake effect.Pay attention to leaving enough braking distance during the running -in.
PROCEDURE:
●
Disassembling tires and rotor components
Tire and rotor components are removed with two bolts on the left front shock absorbing bottom b with 6#inner
hexagonal.First hold the front wheels and then remove the hollow shaft with 17#inner hexagonal, remove the
left axis sleeve
⑶
. Remove the two bolts of the front shock absorbing bottom A. Put the right fixed shaft sleeve
⑻
and the right axis set.
●
Brake discs, ABS gear
Disastern 5 bolts with 6#inner hexagonal in the brake disc, ABS tooth barrel, and protect the brake disc in the
surroundings of rivets or double -sided glue around the rivet. Pack the drum, remove the ABS gear
⑷
and brake
disk.
●
Tires and rotation components
Tire and rotor components first unscrew the valve cap
①
to release the gas, remove the tire
⑾
with a
professional tire pulling machine, and avoid the position of the tire pressure sensor when pulling the
tire.Remove the nut with the 12#wrench
②
and remove the pad
③
.Finally remove the tire pressure sensor
④
.
CAUTION:
●
Use suitable tools to support the entire vehicle to prevent accidents caused by the vehicle dumping during
disassembly; it is strictly forbidden to operate single.
●
Be careful when disassembling tires and wheels to prevent damage.
●
After replacing the tire, check whether the air leakage and the balance of the movement.
●
Insufficient air pressure on the tire may cause turning jitter, abnormal wear, etc.; There is a risk of explosive
tires in summer tire pressure.
●
Because the tire self -replenishment may block the pores of the tire pressure monitoring sensor, it should not
be used when the pores of the tire pressure monitoring sensor cause inflatable difficulty or the tire pressure
monitoring failure.
2
Fig.9 FRONT FORK
COMPONENT
ZT350-GK front aluminum wheel (MT3.5×
17/black/single disc)
1094300-007021 10 1
Front wheel component
3 1274300-008000
ZT350-GK front wheel bushing (φ20×φ28×
15.5/shoulder outer diameterφ34)