Zontes ZT350-EURO V 2022, Руководство по обслуживанию

Страница: 58 / 118

8-FRONT FORK COMPONENT
57
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1 1244300-042000 ZT350 Rubber Wire Buckle (Double Buckle Type) 2
2 1274300-025000 ZT350-R water tank water inlet fixing bracket 1
3 1154300-004000 ZT350-X throttle refueling cable 1
4 1154300-005000 ZT350-X throttle return cable 1
5 1244100-042000 ZT250-R right handle bar rubber sleeve 1
6 1184200-140000 ZT310-X1 Right Handle Switch 1
7 1250205-031091 GB70.1M6×30(stainless steel) 2
PROCEDURE:
●
Remove the throttle line
Plurry the throttle first unbutton the two line buckles.Unplug the temperature sensor of the empty filter of the
arrow A.
Use 10#Open wrench to rot the throttle refueling line
②
to rotate up to the end, the nut
④
rotation of the
adjustment tube
①
; remove the cylindrical connector of the refueling line from the turntable; The thread of the
thread
②
and
④
, remove the cylindrical connector from the turntable, then move the regulatory tube of the fuel
line
⑷
to move over the bracket on the throttle
③
.
Put the throttle line from the gap of the stent in the water tank with the water outlet.
Use 5#Inner hexagonal tools to loosen the bolts; put the secondary switch
⑻
and the right disc brake rocker
rocker component to the direction of the arrow and lock the bolt
⑺
.The main pump of the disc brake should
always be kept at a high position to prevent the air from entering the oil circuit.
Use your hand to hold the right hand to put the switch
⑹
, first remove the bolt of bolts in 5#hexagonal, then
remove the bolt
⑥
.Open the handlebars and parts.
Put the throttle line from the right hand to remove the core turntable of the glue cover, and finally remove it
from the lava hole in the lower part of the switch.
●
Install the throttle line
Put the accelerator line into the cable hole in the lower part of the switch.Put the cylindrical connector of the
throttle line into the right hand to put the core turntable on the coat. Inste the bolt of the fuel wire to the restricted
card slot on the refueling line, lock the bolt in the 5#hexagonal tool, and the torque is 8-10N.M. The switch is
equipped with a tie bolt for a few times, and then observes the positioning hole and direction of the lower part of
the switch
⑹
to lock the bolt and bolt
⑨
. Finally lock the bolt again. Subtulate the auxiliary switch and rocker
arms, pay attention to the symbols of the switching switch.
Put the accelerator from the gap of the water tank with the water outlet fixed bracket.
Use 10#Open wrench to push the throttle refueling wire or the nut of the oil line
②
to rotate up to the end, and
the nut
④
rotation out of the adjustment pipe
①
.
Put the back to the bracket
③
, and then put the connector into the turntable
⑤
.
Put the refueling line into the bracket
③
, and then put the rotating turntable
⑤
at a certain angle.
Refer to the method of adjusting the gap to adjust the tapecal gap; after adjusting the left and right
rotation directions, the idle speed should not be changed and the reset is flexible. Locking nut
②
and
④
.
CAUTION:
●
During the disassembly process, the vehicle should be fixed to prevent accidental accidents.
●
Removal of the throttle line needs to be disassembled the cushion, fuel tank assembly, surrounding, and
side caps.
Fig.3 FRONT FORK
COMPONENT
Replace the throttle
ZT350-X second generation right handle switch (dark
gray TFT-750)
1 1184300-018000 8