Zontes ZT350-EURO V 2022, Руководство по обслуживанию

Страница: 106 / 118

14-REAR COVER COMPONENT
105
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1 1224200-161000 ZT310-R electric device box (colloid battery) 1
2 1184100-010000 ZT250-S starting relay 1
3 1244200-111000 ZT310 gel battery strap 1
4 1184200-099000 ZT310 colloid battery (6-FM-10/10Ah) 1
5 1251112-001093 M6×16 Hexagon flange bolts (color Zinc) 2
6 1274100-057095 Flanging bushing φ6.2×φ8.4×3.5
＋
φ14×1.5 2
7 1244100-052000 Buffer rubber of flanging bushing (φ8.5×φ14×1) 2
8 1224300-059000 ZT350-GK taillight plug holder 1
9 1180300-101000 HJ150-3 square flasher (LED) 1
10 1224300-054000 ZT350-GK relay holder 1
11 1184100-017000 ZT250-S fuel-injection relay 5
12 1244200-103000 ZT310 relay rubber sleeve 5
The cable end Fuel-injection relay
Fig.2 REAR COVER
COMPONENT
ZT310 colloid battery assembly
CAUTION:
●
During the disassembly process, the material should be protected to prevent damage to the paint
surface.
●
Be careful not to press any cables when reinstallation to prevent short circuits.
PROCEDURE:
●
Start relay
Start the relay and hold the buckle referred to the arrow to remove the electrical device box.Open the red
rubber hat
③
of the launching relay
⑵
and the black rubber hat
④
, remove the built -in nut with the
10#sleeve.Pull out the yellow/red and green/red line plugs.Pull up the relay up and remove it.
When reinstallation, the relay yellow/red and green/red line corresponds to the color of the main cable, and
the nut does not need to distinguish.Make sure that the protective cap is covered after the nut is tightened, and
the electrical component box is inserted. See the figure below for the starting process of launching relay failure.
●
Battery
The battery will bind a strap. The end of the battery is stretched and pressed down the metal ring down, and
the limited buckle of the electrical component box is bypass.
Pull out the battery , open the positive red rubber hat
③
, remove the bolt of the battery with a cross
screwdriver or 10#sleeve.Then open the negative black rubber hat
④
remove the bolt. Take the battery from
the vehicle and place it.
Use a multimeter to measure the battery voltage. If it is lower than 12.8 volts, it should be charged in
time.The battery should be removed for a long time without using a vehicle and charged once a month.
●
Relay holder,tail lamp piug holder
Revisit with 8#sleeves to remove the fixed seat
⑻
and fixed seats with 8#sleeves, remove the bolt
⑸
on the
fixed seat, and remove the band
⑹
and buffer glue.
Unplug the plug of the flash device, and take the flash device from the fixed seat.
Pull out the 4 -piece relay rubber sleeve. After removing, you can see the Electic Jet Relax.
⑤
It is the oil
pump relay,
⑥
as the main relay,
⑦
to start the auxiliary relay,
⑧
is the cooling fan relay, and the lamp as the
light relay; the sorting batch may be different, and the corresponding text description is printed on the cable
plug. You can see after setting.
If you need to check whether it is damaged, pull it off and turn it to the side of the plug -in film. As shown in
Figure 3 and 5, it is a normal closed contact. You can use a universal watch bee to test.1 and 2 are regular
contacts.Otherwise, it can be judged as a relay failure.